ADG513BNZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 2 weeks ago) |
| Mounting Type | Through Hole |
| Package / Case | 16-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 16 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 30Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 10μW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | NOT APPLICABLE |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Time@Peak Reflow Temperature-Max (s) | NOT APPLICABLE |
| Base Part Number | ADG513 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 4 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 4.5V |
| Power Dissipation | 10μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 375 ns |
| Voltage - Supply, Single/Dual (±) | 3V~5.5V ±4.5V~5.5V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 150 ns |
| Max Dual Supply Voltage | 5.5V |
| On-State Resistance (Max) | 30Ohm Typ |
| Min Dual Supply Voltage | 4.5V |
| Screening Level | MIL-STD-883 |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 9pF |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 200ns, 120ns (Typ) |
| Charge Injection | 11pC |
| Crosstalk | -85dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Height Seated (Max) | 5.33mm |
| Length | 20.13mm |
| Width | 7.62mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG513BNZ Overview
Shipping overseas is convenient with the electronic component packed in 16-DIP (0.300, 7.62mm). The advanced packaging method Tube provides high reliability. This analog switch is mounted in Through Hole. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature around -40°C~85°C TA extended. In total, there have been 16 terminations. High-quality output is provided by the electronic component's 4 channels. When a voltage supply of 5V is used, the electronic component should be turned on and run. An electrical component of this type can be found in the 16 series. Multiplexers built on a SPST - NO/NC switching circuit are built. Try searching for the analog switch ic with ADG513 if you are looking for variants. An switch multiplexer with 30Ohm internal resistance has a value of 30Ohm. For details about the functions of 16 pins, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. Multiplexers should not be powered above 5.5V in normal situations. A analog switch ic that has a cost-effective Dual, Single supply type. It is recommended that the electrical component receives a voltage of 4.5V. A voltage higher than 1μA may cause damage to the switch multiplexer. For this switch, a dual supply voltage is feasible, but it must not exceed 5.5VA dual power supply should have at least 4.5V voltage attached. This analog switch ic utilizes SEPARATE OUTPUT output.
ADG513BNZ Features
4 Channels
Switch Circuit: SPST - NO/NC
ADG513BNZ Applications
There are a lot of Analog Devices Inc. ADG513BNZ Analog Switches & Multiplexers ICs applications.
- Communication systems
- Optical Applications
- SONET
- PDAs
- Cell phones
- Medical Instrumentation
- Communications systems
- Remote Powered Equipment
- Cellular phones
- Intelligent PBX
