Parameters |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
375 ns |
Voltage - Supply, Single/Dual (±) |
3V~5.5V ±4.5V~5.5V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
150 ns |
Max Dual Supply Voltage |
5.5V |
On-State Resistance (Max) |
30Ohm Typ |
Min Dual Supply Voltage |
4.5V |
Dual Supply Voltage |
5V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
68 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
9pF 9pF |
Switch Circuit |
SPST - NO/NC |
Switch Time (Ton, Toff) (Max) |
200ns, 120ns (Typ) |
Charge Injection |
11pC |
Crosstalk |
-85dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Height Seated (Max) |
1.75mm |
Length |
9.9mm |
Width |
3.9mm |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 3 weeks ago) |
Mounting Type |
Surface Mount |
Package / Case |
16-SOIC (0.154, 3.90mm Width) |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
30Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
10μW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
5V |
Terminal Pitch |
1.27mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG513 |
Output |
SEPARATE OUTPUT |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Number of Channels |
4 |
Interface |
Parallel |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
4.5V |
Operating Supply Current |
100pA |
Power Dissipation |
10μW |
ADG513BRZ-REEL7 Overview
Shipping overseas is convenient due to the electrical component's packing in 16-SOIC (0.154, 3.90mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have the same number of circuits 1:1. Around -40°C~85°C TA is the extended operating temperature. 16 terminations have been made so far. This electronic part offers high-quality output due to its 4 channels. Turning on and running the electrical part should be easy with a 5V voltage supply. Electronic part bodies are injected with 16 pins. The analog switch ics are built using SPST - NO/NC switching circuits. Using the ADG513 search parameter, you can discover variants of the switch. The internal resistance of this digital multiplexer is 30Ohm. Datasheets for 16 pin functions are available upon request. This switch device is a typical Multiplexer or Switches. A voltage higher than 5.5V should not normally be supplied to the switches. The digital multiplexer has a low cost Dual, Single supply. In order for the electronic part to function properly, the lowest voltage should be 4.5V. The analogue multiplexer could operate on 100pA current. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 5.5V. A dual power supply should have at least 4.5V voltage attached. The digital multiplexer has SEPARATE OUTPUT outputs that can be used.
ADG513BRZ-REEL7 Features
4 Channels
Switch Circuit: SPST - NO/NC
100pA Supply Current
ADG513BRZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG513BRZ-REEL7 Analog Switches & Multiplexers ICs applications.
- Ultrasound
- Industrial
- Communications systems
- T1/E1 Terminals
- Fault Tolerant Systems
- 65 V DACs
- Low-Voltage
- Wireless Local Loop
- RGB switches
- Medical