ADG5207BRUZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 28-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 28 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Resistance | 160Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.1mW |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Number of Functions | 1 |
| Terminal Pitch | 0.635mm |
| Base Part Number | ADG5207 |
| Pin Count | 28 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 36V |
| Number of Channels | 8 |
| Number of Circuits | 2 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 9V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Nominal Supply Current | 80μA |
| Power Dissipation | 1.1mW |
| Max Supply Current | 130μA |
| Turn On Delay Time | 295 ns |
| Number of Inputs | 16 |
| Voltage - Supply, Single/Dual (±) | 9V~40V ±9V~22V |
| Turn-Off Delay Time | 270 ns |
| Max Dual Supply Voltage | 22V |
| -3db Bandwidth | 145MHz |
| On-State Resistance (Max) | 160Ohm |
| Min Dual Supply Voltage | 9V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 3.3pf 32pF |
| Switch Time (Ton, Toff) (Max) | 230ns, 185ns |
| Charge Injection | 0.45pC |
| Channel-to-Channel Matching (ΔRon) | 4 Ω |
| Crosstalk | -76dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 370ns |
| Signal Current-Max | 0.03A |
| Height | 1.05mm |
| Length | 9.8mm |
| Width | 4.5mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG5207BRUZ Overview
The electronic part can be shipped overseas conveniently because it is packaged in 28-TSSOP (0.173, 4.40mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tube. Surface Mount is where this multiplexer is located. The ratio between the number of multiplexer and demultiplexer circuits is 8:1. Operating temperature extended to -40°C~125°C TA. The total number of terminations is 28. As a result of its 8 channels, this electronic component provides high-quality output. An injection of 28 pins is performed into the body of the electrical component. Circuits number 2 make up this analogue multiplexer. Try searching for ADG5207 variants of the analog switch ic. This digital multiplexer has 160Ohm internal resistance. The functions of 28 pins can be found in the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. It is generally not recommended to supply a voltage higher than 40V to the switch device in normal circumstances. A low voltage of 9V should be applied to the electronic component. If you put voltage higher than 130μA on the digital multiplexer, damage may occur. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. If you are using dual power supplies, you should attach at least 9V. It is integrated with a DIFFERENTIAL MULTIPLEXER analog IC. 36V operating voltages are supported by the electronic component. Operating the 16 inputs requires 16 inputs.
ADG5207BRUZ Features
8 Channels
-3db Bandwidth: 145MHz
ADG5207BRUZ Applications
There are a lot of Analog Devices Inc. ADG5207BRUZ Analog Switches & Multiplexers ICs applications.
- E1 Multiplexer
- Private Branch Exchange (PBX)
- Medical Instrumentation
- Remote wireless modules
- ISDN NT1/TA
- USB 1.1 signal switching circuits
- Audio/video switches
- Digital access cross connects
- Wireless Local Loop
- Mechanical reed relay replacement
