ADG5234BCPZ-RL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Mounting Type | Surface Mount |
| Package / Case | 20-WFQFN Exposed Pad, CSP |
| Surface Mount | YES |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 200Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1.1mW |
| Technology | BICMOS |
| Terminal Position | QUAD |
| Number of Functions | 4 |
| Terminal Pitch | 0.5mm |
| Base Part Number | ADG5234 |
| Output | SEPARATE OUTPUT |
| Pin Count | 20 |
| Interface | Parallel |
| Number of Circuits | 4 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 9V |
| Test Frequency | 1MHz |
| Power Dissipation | 1.1mW |
| Max Supply Current | 55μA |
| Turn On Delay Time | 175 ns |
| Voltage - Supply, Single/Dual (±) | 9V~40V ±9V~22V |
| Supply Type | Dual, Single |
| Bandwidth | 205MHz |
| Turn-Off Delay Time | 155 ns |
| Max Dual Supply Voltage | 22V |
| -3db Bandwidth | 370MHz |
| On-State Resistance (Max) | 160Ohm |
| Min Dual Supply Voltage | 9V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 4.5pF 10pF |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 200ns, 95ns |
| Insertion Loss (dB) | -6.3 dB |
| Charge Injection | 0.7pC |
| Channel-to-Channel Matching (ΔRon) | 3.5 Ω |
| Crosstalk | -80dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 305ns |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG5234BCPZ-RL7 Overview
Packed in 20-WFQFN Exposed Pad, CSP, the electronic component is convenient for shipping overseas. High reliability is provided by advanced packaging method Tape & Reel (TR). In Surface Mount, you'll find this switch device. 2:1 is the ratio between multiplexers and demultiplexers. Temperatures around -40°C~125°C TA are extended for operation. In total, 20 terminations have occurred. An electrical component like this is included in the 20 series. Circuits based on SPDT switching are used to construct these analog switch ics. A total of 4 circuits make up this switch device. Try searching with ADG5234 if you're looking for variants. Internally, this switch multiplexer has a resistance of 200Ohm. For functions related to 20 pins, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. Users shouldn't supply more than 40V voltage to the switch device. A analog switch ic that has a cost-effective Dual, Single supply type. There should be 9V voltage fed to the electrical part below 9V. Put voltage above 55μA on the multiplexer to cause damage. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. If you are using dual power supplies, you should attach at least 9V. In this switch multiplexer, there are SEPARATE OUTPUT outputs available. In 205MHz-bandwidths, data can be transferred.
ADG5234BCPZ-RL7 Features
Switch Circuit: SPDT
-3db Bandwidth: 370MHz
Bandwidth: 205MHz
ADG5234BCPZ-RL7 Applications
There are a lot of Analog Devices Inc. ADG5234BCPZ-RL7 Analog Switches & Multiplexers ICs applications.
- Communication systems
- Avionics test equipment
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Remote wireless modules
- PCMCIA cards
- Medical systems
- Fiber In The Loop (FITL)
- Video signal routing
- Audio/video switches
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
