ADG5249FBRUZ
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 20-TSSOP (0.173, 4.40mm Width) |
| Number of Pins | 20 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| Resistance | 335Ohm |
| Terminal Finish | Tin (Sn) |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG5249 |
| Pin Count | 20 |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 8V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Voltage - Supply, Single/Dual (±) | 8V~44V ±5V~22V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 22V |
| -3db Bandwidth | 320MHz |
| On-State Resistance (Max) | 335Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 75 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 4pF 7pF |
| On-state Resistance Match-Nom | 2.5Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 245ns, 135ns |
| Charge Injection | -1.2pC |
| Channel-to-Channel Matching (ΔRon) | 3 Ω |
| Crosstalk | -75dB @ 1MHz |
| Switch-on Time-Max | 315ns |
| Switch-off Time-Max | 160ns |
| Length | 6.5mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG5249FBRUZ Overview
Packed in 20-TSSOP (0.173, 4.40mm Width), the electronic component is convenient for shipping overseas. High reliability is ensured by the advanced packaging method Tube. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a ratio of 4:1. Around -40°C~125°C TA is the extended operating temperature. In total, there have been 20 terminations. High-quality output is provided by the electronic component's 4 channels. An 15V voltage supply should allow the electrical part to be turned on and run. This electronic part can be found in the 20 series. Circuits based on SP4T switching are used to construct these analog switch ics. Circuits number 2 make up this analogue multiplexer. Try searching with ADG5249 to find analog multiplexer variants. An switch multiplexer with 335Ohm internal resistance has a value of 335Ohm. Please refer to the datasheets for 20 pins functions. Users shouldn't supply more than 44V voltage to the switch device. It is recommended that the electrical component receives a voltage of 8V. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 22V. The voltage should be at least 5V if you are using dual power supplies. An analog IC with the number DIFFERENTIAL MULTIPLEXER is integrated into this board.
ADG5249FBRUZ Features
4 Channels
Switch Circuit: SP4T
-3db Bandwidth: 320MHz
ADG5249FBRUZ Applications
There are a lot of Analog Devices Inc. ADG5249FBRUZ Analog Switches & Multiplexers ICs applications.
- Signal routing between systems
- E1 Multiplexer
- Industrial and process control systems
- Relay Replacement
- Data switching
- DSLAMs
- PDAs
- Access Concentrators
- Central office
- E1 Network Equipment
