ADG526AKN
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 28-DIP (0.600, 15.24mm) |
| Surface Mount | NO |
| Number of Pins | 28 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Resistance | 700Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Peak Reflow Temperature (Cel) | NOT APPLICABLE |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT APPLICABLE |
| Base Part Number | ADG526 |
| Pin Count | 28 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Channels | 16 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 10.8V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Operating Supply Current | 1.5mA |
| Power Dissipation | 26mW |
| Max Supply Current | 1.5mA |
| Propagation Delay | 300 ns |
| Turn On Delay Time | 450 ns |
| Voltage - Supply, Single/Dual (±) | 10.8V~16.5V ±10.8V~16.5V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 450 ns |
| Max Dual Supply Voltage | 16.5V |
| On-State Resistance (Max) | 450Ohm |
| Min Dual Supply Voltage | 10.8V |
| High Level Output Current | 20mA |
| Dual Supply Voltage | 12V |
| Multiplexer/Demultiplexer Circuit | 16:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 44pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Time (Ton, Toff) (Max) | 300ns, 300ns |
| Charge Injection | 4pC |
| Channel-to-Channel Matching (ΔRon) | 22.5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.02A |
| Height | 4.95mm |
| Length | 39.75mm |
| Width | 14.73mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG526AKN Overview
Shipping overseas is convenient with the electronic component packed in 28-DIP (0.600, 15.24mm). This high-reliability packaging method uses advanced packaging methods Tube. Mounted in Through Hole is this multiplexer. 16:1 is the ratio between multiplexers and demultiplexers. Increasing operating temperature to around -40°C~85°C TA. A total of 28 terminations have been recorded. The electronic part provides high-quality output because it has 16 channels. When a voltage supply of 15V is used, the electronic component should be turned on and run. This electrical component is included in the 28 series of products. The multiplexer consists of 1 circuits. Search with ADG526 if you are looking for analog multiplexer variants. The internal resistance of this digital multiplexer is 700Ohm. To find out what the 28 pins do, please refer to the datasheets. The analog multiplexer shown here is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 16.5V volts for the multiplexer. The lowest voltage the electronic part should receive is 10.8V. An operating current of 1.5mA would be sufficient for this switch device. When the digital multiplexer is charged above 1.5mA, damage can occur. If put voltage greater than 16.5V on the multiplexer, damage may be caused to the device. A dual power supply should have at least 10.8V voltage attached. There is an analog IC SINGLE-ENDED MULTIPLEXER integrated with this board. The electronic component can function from 15V.
ADG526AKN Features
16 Channels
1.5mA Supply Current
ADG526AKN Applications
There are a lot of Analog Devices Inc. ADG526AKN Analog Switches & Multiplexers ICs applications.
- Audio and video routing
- Precision data acquisition
- Frame Relay Equipment
- Fiber to the Home
- Video signal routing
- Remote wireless modules
- SONET/SDH ADM
- Routers
- Industrial
- Medical systems
