Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 1 week ago) |
Mounting Type |
Surface Mount |
Package / Case |
28-LCC (J-Lead) |
Surface Mount |
YES |
Number of Pins |
28 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
3 (168 Hours) |
Number of Terminations |
28 |
ECCN Code |
EAR99 |
Resistance |
450Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
470mW |
Technology |
CMOS |
Terminal Position |
QUAD |
Terminal Form |
J BEND |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
15V |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
ADG526 |
Pin Count |
28 |
Number of Channels |
16 |
Interface |
Parallel |
Number of Circuits |
1 |
Max Supply Voltage |
16.5V |
Min Supply Voltage |
10.8V |
Analog IC - Other Type |
SINGLE-ENDED MULTIPLEXER |
Nominal Supply Current |
1.5mA |
Power Dissipation |
26mW |
Propagation Delay |
300 ns |
Turn On Delay Time |
600 ns |
Number of Inputs |
16 |
Voltage - Supply, Single/Dual (±) |
10.8V~16.5V ±10.8V~16.5V |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
600 ns |
Max Dual Supply Voltage |
16.5V |
On-State Resistance (Max) |
450Ohm |
Min Dual Supply Voltage |
10.8V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
16:1 |
Off-state Isolation-Nom |
68 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
5pF 44pF |
On-state Resistance Match-Nom |
5Ohm |
Switch Time (Ton, Toff) (Max) |
300ns, 300ns |
Charge Injection |
4pC |
Channel-to-Channel Matching (ΔRon) |
22.5 Ω |
Switching |
BREAK-BEFORE-MAKE |
Drain to Source Resistance |
300Ohm |
Signal Current-Max |
0.02A |
Height |
3.94mm |
Length |
11.58mm |
Width |
11.58mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG526AKPZ Overview
Presented in 28-LCC (J-Lead), this electrical component is convenient for overseas shipping. Advanced packaging method Tube is used to provide high reliability. In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have the same number of circuits 16:1. Extended operating temperature around -40°C~85°C TA. The total number of terminations is 28. This electronic part offers high-quality output due to its 16 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. There are 28 pins injected into the electronic part body. 1 circuits are used in this analogue multiplexer. Try searching for ADG526 variants of the analog switch ic. It has an internal resistance of 450Ohm. To find out what the 28 pins do, please refer to the datasheets. This switch device is a typical Multiplexer or Switches. Users should never supply a voltage higher than 16.5V to a switch device. The lowest voltage fed to the electronic component should be 10.8V. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 16.5V. The voltage should be at least 10.8V if you are using dual power supplies. Integrated with an analog IC SINGLE-ENDED MULTIPLEXER. In order to operate the 16 inputs, there are several steps to follow. A Drain to Source resistance of 300Ohm is shown for this electronic part.
ADG526AKPZ Features
16 Channels
Drain-to-Source resistance: 300Ohm
ADG526AKPZ Applications
There are a lot of Analog Devices Inc. ADG526AKPZ Analog Switches & Multiplexers ICs applications.
- Digital access cross connects
- New designs requiring multiplexer functions
- Switching Systems
- Central office
- FTTH
- High-Voltage
- Fiber In The Loop (FITL)
- Imaging
- Digital Cross-Connects
- Microwave transmission systems