ADG527AKPZ
| Parameters | |
|---|---|
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 3 (168 Hours) |
| Number of Terminations | 28 |
| ECCN Code | EAR99 |
| Resistance | 450Ohm |
| Terminal Finish | MATTE TIN |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 28mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | J BEND |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADG527 |
| Pin Count | 28 |
| Qualification Status | Not Qualified |
| Number of Channels | 8 |
| Interface | Parallel |
| Number of Circuits | 2 |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 10.8V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Power Dissipation | 26mW |
| Turn On Delay Time | 400 ns |
| Number of Inputs | 16 |
| Voltage - Supply, Single/Dual (±) | 10.8V~16.5V ±10.8V~16.5V |
| Supply Current-Max (Isup) | 1.5mA |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 400 ns |
| Max Dual Supply Voltage | 16.5V |
| On-State Resistance (Max) | 450Ohm |
| Min Dual Supply Voltage | 10.8V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 44pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Time (Ton, Toff) (Max) | 300ns, 300ns |
| Charge Injection | 4pC |
| Channel-to-Channel Matching (ΔRon) | 22.5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 300ns |
| Switch-off Time-Max | 300ns |
| Drain to Source Resistance | 300Ohm |
| Height | 4.06mm |
| Length | 11.58mm |
| Width | 11.582mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 week ago) |
| Mounting Type | Surface Mount |
| Package / Case | 28-LCC (J-Lead) |
| Surface Mount | YES |
| Number of Pins | 28 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
ADG527AKPZ Overview
Due to its 28-LCC (J-Lead) packaging, the electronic part is convenient for international shipping. The advanced packaging method Tube provides high reliability. Surface Mount is where this multiplexer is located. 8:1 is the number of circuits in the multiplexer and demultiplexer. The operating temperature is extended to around -40°C~85°C TA. In total, there have been 28 terminations. This electronic part offers high-quality output due to its 8 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. Into the electrical component body are injected 28 pins. It consists of 2 circuits. Try searching with ADG527 to find analog multiplexer variants. Internally, this switch multiplexer has a resistance of 450Ohm. To find out what the functions of 28 pins are, please refer to their datasheets. This switch device is a typical Multiplexer or Switches. A voltage higher than 16.5V should not normally be supplied to the switches. 10.8V is the lowest voltage that should be fed to the electronic electronic part. Despite this switch's dual supply capability, its voltage should not exceed 16.5V. With dual power supplies, you should attach at least 10.8V. There is an analog IC DIFFERENTIAL MULTIPLEXER integrated with this board. Among the inputs that can be operated are the 16 inputs. A Drain to Source resistance of 300Ohm is shown for this electronic part.
ADG527AKPZ Features
8 Channels
Drain-to-Source resistance: 300Ohm
ADG527AKPZ Applications
There are a lot of Analog Devices Inc. ADG527AKPZ Analog Switches & Multiplexers ICs applications.
- PDH Multiplexers
- Microprocessor controlled systems
- Central office
- Industrial and process control systems
- 65 V DACs
- Low-Voltage
- ATM
- Digital cross connects (DSX-1)
- FTTH
- CSU
