ADG528AKN
| Parameters | |
|---|---|
| Mounting Type | Through Hole |
| Package / Case | 18-DIP (0.300, 7.62mm) |
| Surface Mount | NO |
| Number of Pins | 18 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 18 |
| ECCN Code | EAR99 |
| Resistance | 450Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Peak Reflow Temperature (Cel) | NOT APPLICABLE |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 2.54mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | NOT APPLICABLE |
| Base Part Number | ADG528 |
| Pin Count | 18 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Channels | 8 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 10.8V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Power Dissipation | 28mW |
| Throw Configuration | DPST |
| Propagation Delay | 300 ns |
| Turn On Delay Time | 450 ns |
| Voltage - Supply, Single/Dual (±) | 10.8V~16.5V ±10.8V~16.5V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 450 ns |
| Max Dual Supply Voltage | 16.5V |
| On-State Resistance (Max) | 450Ohm |
| Min Dual Supply Voltage | 10.8V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 22pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Time (Ton, Toff) (Max) | 300ns, 300ns |
| Charge Injection | 4pC |
| Channel-to-Channel Matching (ΔRon) | 22.5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.02A |
| Height Seated (Max) | 4.57mm |
| Width | 7.62mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG528AKN Overview
Shipping overseas is convenient due to the electrical component's packing in 18-DIP (0.300, 7.62mm). In order to provide high reliability, an advanced packaging method Tube is used. Mounted in Through Hole is this multiplexer. In the multiplexer and demultiplexer, 8:1 represents the number of circuits. Operating temperature extended to -40°C~85°C TA. Totally, there are 18 terminations. The electronic part delivers high-quality output through its 8 channels. An 15V voltage supply should allow the electrical part to be turned on and run. This electrical component is included in the 18 series of products. The multiplexer consists of 1 circuits. Look for analog switch ic variants by searching with ADG528. This digital multiplexer has 450Ohm internal resistance. Datasheets for functions of 18 pins are available. The analog multiplexer shown here is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 16.5V. The digital multiplexer has a low cost Dual, Single supply. 10.8V is the lowest voltage that should be fed to the electronic electronic part. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 16.5V. With dual power supplies, you should attach at least 10.8V. Integrated with SINGLE-ENDED MULTIPLEXER analog IC. There is a voltage range of 15V operating voltages for the electrical part.
ADG528AKN Features
8 Channels
ADG528AKN Applications
There are a lot of Analog Devices Inc. ADG528AKN Analog Switches & Multiplexers ICs applications.
- Medical systems
- Precision instrumentation
- DSLAMs
- Cellular phones
- E1 Multiplexer
- DSUs
- Digital access cross connects
- CSU
- Modems
- Relay Replacement
