ADG528AKP
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 20-LCC (J-Lead) |
| Surface Mount | YES |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 450Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | J BEND |
| Peak Reflow Temperature (Cel) | 225 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG528 |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Channels | 8 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 10.8V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Operating Supply Current | 1.5mA |
| Power Dissipation | 28mW |
| Throw Configuration | DPST |
| Propagation Delay | 300 ns |
| Turn On Delay Time | 450 ns |
| Number of Inputs | 8 |
| Voltage - Supply, Single/Dual (±) | 10.8V~16.5V ±10.8V~16.5V |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 450 ns |
| Max Dual Supply Voltage | 16.5V |
| On-State Resistance (Max) | 450Ohm |
| Min Dual Supply Voltage | 10.8V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 22pF |
| On-state Resistance Match-Nom | 5Ohm |
| Switch Time (Ton, Toff) (Max) | 300ns, 300ns |
| Charge Injection | 4pC |
| Channel-to-Channel Matching (ΔRon) | 22.5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.02A |
| Height Seated (Max) | 4.57mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG528AKP Overview
This electronic part is conveniently packaged in 20-LCC (J-Lead), making it easy to ship abroad. The advanced packaging method Tube provides high reliability. There is an analog multiplexer mounted in position Surface Mount. In the multiplexer and demultiplexer, 8:1 represents the number of circuits. The operating temperature is extended to around -40°C~85°C TA. 20 terminations have been made so far. A high-quality output is provided by the electrical component's 8 channels. With a 15V voltage supply, the electrical component should be turned on and run. There are 20 pins injected into the electronic part body. Circuits number 1 make up this analogue multiplexer. Try searching with ADG528 if you're looking for variants. As far as internal resistance is concerned, it has 450Ohm. The datasheets for the 20 pins explain the functions. Multiplexer or Switches is a typical switch device. A voltage higher than 16.5V should not normally be supplied to the switches. 10.8V is the lowest voltage the electrical component should receive. For this multiplexer to operate, 1.5mA current would be sufficient. For this multiplexer, dual supply voltage is feasible, but it should not exceed 16.5V. You should attach at least 10.8V voltage if you are using dual power supply. Integrated with SINGLE-ENDED MULTIPLEXER analog IC. There is a voltage range of 15V operating voltages for the electrical part. The 8 inputs need to be operated in order to work.
ADG528AKP Features
8 Channels
1.5mA Supply Current
ADG528AKP Applications
There are a lot of Analog Devices Inc. ADG528AKP Analog Switches & Multiplexers ICs applications.
- Power routing
- Fiber to the Home
- Industrial and process control systems
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Mechanical reed relay replacement
- High-Voltage
- PCMCIA cards
- Medical Instrumentation
- Voice over IP/DSL – Integrated Access Devices, Smart
- Audio and video routing
