ADG528AKP-REEL
| Parameters | |
|---|---|
| On-state Resistance Match-Nom | 5Ohm |
| Switch Time (Ton, Toff) (Max) | 300ns, 300ns |
| Charge Injection | 4pC |
| Channel-to-Channel Matching (ΔRon) | 22.5 Ω |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.02A |
| Height Seated (Max) | 4.57mm |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Mounting Type | Surface Mount |
| Package / Case | 20-LCC (J-Lead) |
| Surface Mount | YES |
| Number of Pins | 20 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 20 |
| ECCN Code | EAR99 |
| Resistance | 450Ohm |
| Max Power Dissipation | 470mW |
| Technology | CMOS |
| Terminal Position | QUAD |
| Terminal Form | J BEND |
| Peak Reflow Temperature (Cel) | 225 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG528 |
| Pin Count | 20 |
| Qualification Status | Not Qualified |
| Operating Supply Voltage | 15V |
| Number of Channels | 8 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 16.5V |
| Min Supply Voltage | 10.8V |
| Operating Supply Current | 600μA |
| Power Dissipation | 28mW |
| Throw Configuration | DPST |
| Propagation Delay | 300 ns |
| Turn On Delay Time | 450 ns |
| Logic Function | Multiplexer |
| Voltage - Supply, Single/Dual (±) | 10.8V~16.5V ±10.8V~16.5V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 450 ns |
| Max Dual Supply Voltage | 16.5V |
| On-State Resistance (Max) | 450Ohm |
| Min Dual Supply Voltage | 10.8V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 68 dB |
| Current - Leakage (IS(off)) (Max) | 1nA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 22pF |
ADG528AKP-REEL Overview
This electronic part is conveniently packaged in 20-LCC (J-Lead), making it easy to ship abroad. Advanced packaging method Tape & Reel (TR) is used to provide high reliability. Surface Mount is where this multiplexer is located. 8:1 is the ratio of multiplexer to demultiplexer circuits. The operating temperature is extended to around -40°C~85°C TA. In total, there have been 20 terminations. As a result of its 8 channels, this electronic component provides high-quality output. It is safe to turn on and run the electronic component with a 15V voltage supply. The electrical component body receives 20 pins. The circuits in this analogue multiplexer number 1. Try searching with ADG528 to find analog multiplexer variants. Analog switches have 450Ohm internal resistance. Please refer to the datasheets for 20 pins functions. Multiplexers should not be powered above 16.5V in normal situations. Analogue multiplexer with a Dual, Single supply type that is cost-effective. A low voltage of 10.8V should be applied to the electronic component. For this digital switch to work, 600μA current would suffice. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 16.5V. If you are using a dual power supply, you should attach at least 10.8V. 15V operating voltages can be used with this electrical part.
ADG528AKP-REEL Features
8 Channels
600μA Supply Current
ADG528AKP-REEL Applications
There are a lot of Analog Devices Inc. ADG528AKP-REEL Analog Switches & Multiplexers ICs applications.
- Cable Modem
- High reliability control systems
- Communication systems
- Medical systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Audio and video routing
- Remote wireless modules
- Medical Instrumentation
- Microwave transmission systems
- Access Concentrators
