Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 2 weeks ago) |
Mounting Type |
Through Hole |
Package / Case |
18-CDIP (0.300, 7.62mm) |
Surface Mount |
NO |
Number of Pins |
18 |
Operating Temperature |
-55°C~125°C TA |
Packaging |
Tube |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
18 |
ECCN Code |
EAR99 |
Resistance |
450Ohm |
Terminal Finish |
Tin/Lead (Sn63Pb37) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
470mW |
Technology |
CMOS |
Terminal Position |
DUAL |
Peak Reflow Temperature (Cel) |
NOT APPLICABLE |
Number of Functions |
1 |
Supply Voltage |
15V |
Terminal Pitch |
2.54mm |
Reach Compliance Code |
not_compliant |
Time@Peak Reflow Temperature-Max (s) |
NOT APPLICABLE |
Base Part Number |
ADG528 |
Pin Count |
18 |
Qualification Status |
Not Qualified |
Number of Channels |
8 |
Interface |
Parallel |
Number of Circuits |
1 |
Max Supply Voltage |
16.5V |
Min Supply Voltage |
10.8V |
Analog IC - Other Type |
SINGLE-ENDED MULTIPLEXER |
Operating Supply Current |
600μA |
Power Dissipation |
28mW |
Throw Configuration |
DPST |
Propagation Delay |
300 ns |
Turn On Delay Time |
400 ns |
Voltage - Supply, Single/Dual (±) |
10.8V~16.5V ±10.8V~16.5V |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
400 ns |
Max Dual Supply Voltage |
16.5V |
On-State Resistance (Max) |
450Ohm |
Min Dual Supply Voltage |
10.8V |
Multiplexer/Demultiplexer Circuit |
8:1 |
Off-state Isolation-Nom |
68 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
5pF 22pF |
On-state Resistance Match-Nom |
5Ohm |
Switch Time (Ton, Toff) (Max) |
300ns, 300ns |
Charge Injection |
4pC |
Channel-to-Channel Matching (ΔRon) |
22.5 Ω |
Switching |
BREAK-BEFORE-MAKE |
Signal Current-Max |
0.02A |
Width |
7.62mm |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
ADG528ATQ Overview
Packed in 18-CDIP (0.300, 7.62mm), the electronic component is convenient for shipping overseas. High reliability is achieved by using advanced packaging method Tube. In Through Hole, this analog switch is mounted. Multiplexers and demultiplexers have a ratio of 8:1. Operational temperature extended around -55°C~125°C TA. A total of 18 terminations have been recorded. The electronic part provides high-quality output because it has 8 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. Into the electrical component body are injected 18 pins. 1 circuits are used in this analogue multiplexer. Use ADG528 to search for variants of the digital switches. This digital multiplexer has 450Ohm internal resistance. Datasheets for 18 pin functions are available upon request. In this analog multiplexer, the value is Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 16.5V to the switch device in normal circumstances. In order for the electronic part to function properly, the lowest voltage should be 10.8V. It would be sufficient to run this analogue multiplexer with 600μA current. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 16.5V. The voltage should be at least 10.8V if you are using dual power supplies. A SINGLE-ENDED MULTIPLEXER analog IC is integrated into the board.
ADG528ATQ Features
8 Channels
600μA Supply Current
ADG528ATQ Applications
There are a lot of Analog Devices Inc. ADG528ATQ Analog Switches & Multiplexers ICs applications.
- Industrial control systems
- CSU
- Fault Tolerant Systems
- DSLAMs
- Video signal routing
- USB 1.1 signal switching circuits
- Multi-Line E1 Interface Cards
- Mechanical reed relay replacement
- Cell phones
- Intelligent PBX