Parameters |
Mounting Type |
Through Hole |
Package / Case |
18-DIP (0.300, 7.62mm) |
Surface Mount |
NO |
Number of Pins |
18 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e0 |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
18 |
ECCN Code |
EAR99 |
Resistance |
450Ohm |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Position |
DUAL |
Peak Reflow Temperature (Cel) |
NOT SPECIFIED |
Number of Functions |
1 |
Supply Voltage |
15V |
Reach Compliance Code |
not_compliant |
Time@Peak Reflow Temperature-Max (s) |
NOT SPECIFIED |
Base Part Number |
ADG529 |
Pin Count |
28 |
Qualification Status |
Not Qualified |
Number of Channels |
4 |
Number of Circuits |
2 |
Max Supply Voltage |
16.5V |
Min Supply Voltage |
10.8V |
Analog IC - Other Type |
DIFFERENTIAL MULTIPLEXER |
Power Dissipation |
470mW |
Throw Configuration |
4PST |
Number of Inputs |
8 |
Voltage - Supply, Single/Dual (±) |
10.8V~16.5V ±10.8V~16.5V |
Supply Current-Max (Isup) |
1.5mA |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Max Dual Supply Voltage |
16.5V |
On-State Resistance (Max) |
450Ohm |
Min Dual Supply Voltage |
10.8V |
Multiplexer/Demultiplexer Circuit |
4:1 |
Off-state Isolation-Nom |
68 dB |
Current - Leakage (IS(off)) (Max) |
1nA |
Channel Capacitance (CS(off), CD(off)) |
5pF 11pF |
On-state Resistance Match-Nom |
5Ohm |
Switch Circuit |
SP4T |
Switch Time (Ton, Toff) (Max) |
300ns, 300ns |
Charge Injection |
4pC |
Channel-to-Channel Matching (ΔRon) |
22.5 Ω |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
300ns |
Switch-off Time-Max |
300ns |
Height Seated (Max) |
4.57mm |
RoHS Status |
Non-RoHS Compliant |
ADG529AKN Overview
The electronic component is convenient to ship overseas because it is packed in a 18-DIP (0.300, 7.62mm). High reliability is achieved by using advanced packaging method Tube. In Through Hole, you'll find this switch device. 4:1 is the number of circuits in the multiplexer and demultiplexer. Increasing operating temperature to around -40°C~85°C TA. 18 terminations have been made so far. High-quality output is provided by the electronic component's 4 channels. It is safe to turn on and run the electronic component with a 15V voltage supply. As part of its design, the 28 series is equipped with this electronic component. These analog multiplexers are built based on SP4T switching circuits. 2 circuits are used in this analogue multiplexer. Try searching for the analog switch ic with ADG529 if you are looking for variants. A 450Ohm internal resistance characterizes this multiplexer. To find out what the functions of 18 pins are, please refer to their datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. Multiplexers should not be powered above 16.5V in normal situations. In order for the electronic part to function properly, the lowest voltage should be 10.8V. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 16.5V. The voltage should be at least 10.8V if you are using dual power supplies. With a DIFFERENTIAL MULTIPLEXER analog IC integrated into the board. The electrical component supports 8 inputs.
ADG529AKN Features
4 Channels
Switch Circuit: SP4T
ADG529AKN Applications
There are a lot of Analog Devices Inc. ADG529AKN Analog Switches & Multiplexers ICs applications.
- Industrial control systems
- Microprocessor Controlled Analog Systems
- Power routing
- Cable Modem
- Routers
- Avionics and Military Systems
- CSU
- Access Concentrators
- Voice over IP/DSL – Integrated Access Devices, Smart
- SDH