ADG5401BRMZ
| Parameters | |
|---|---|
| Height | 950μm |
| Length | 3.2mm |
| Width | 3.2mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Weight | 139.989945mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 7Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG5401 |
| Pin Count | 8 |
| Qualification Status | Not Qualified |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 9V |
| Test Frequency | 1MHz |
| Max Supply Current | 55μA |
| Turn On Delay Time | 193 ns |
| Number of Inputs | 1 |
| Voltage - Supply, Single/Dual (±) | 9V~40V ±9V~22V |
| Supply Type | Dual, Single |
| Bandwidth | 170MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 207 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 7Ohm |
| Min Dual Supply Voltage | 9V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 21pF 23pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 21ns, 23ns |
| Charge Injection | 275pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 253ns |
| Switch-off Time-Max | 242ns |
| Normal Position | NO |
ADG5401BRMZ Overview
Packed in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), the electronic component is convenient for shipping overseas. To ensure high reliability, a new packaging method Tube is used. In Surface Mount, you'll find this switch device. Multiplexer and demultiplexer circuits have a number 1:1. An extended operating temperature of -40°C~125°C TA degrees Celsius. In total, there have been 8 terminations. High-quality output is provided by the electronic component's 1 channels. When the electronic component is given a voltage of 15V, it should be turned on and run. It is injected into the electrical part body with 8 pins. Circuits based on SPST - NO switching are used to construct these analog switch ics. Use ADG5401 to search for variants of the digital switches. This digital multiplexer has 7Ohm internal resistance. Please refer to the datasheets for 8 pins functions. In this analog multiplexer, the value is Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 40V. A cost-effective Dual, Single supply type analogue multiplexer. There should be 9V voltage fed to the electrical part below 9V. The analogue multiplexer may be damaged if voltage is greater than 55μA. Despite this switch's dual supply capability, its voltage should not exceed 22V. If you are using dual power supplies, you should attach at least 9V. There are 1 inputs to be operated. There are various bandwidths available for data transfer.
ADG5401BRMZ Features
1 Channels
Switch Circuit: SPST - NO
Bandwidth: 170MHz
ADG5401BRMZ Applications
There are a lot of Analog Devices Inc. ADG5401BRMZ Analog Switches & Multiplexers ICs applications.
- Central office
- Fault Tolerant Systems
- Communication systems
- MP3 players
- Battery Powered Systems
- SDH/SONET multiplexers
- PCMCIA cards
- Avionics test equipment
- DSLAMs
- Data switching
