ADG5401BRMZ-RL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Contact Plating | Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Weight | 139.989945mg |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 7Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1mW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | NOT SPECIFIED |
| Number of Functions | 1 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | NOT SPECIFIED |
| Base Part Number | ADG5401 |
| Qualification Status | Not Qualified |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Number of Circuits | 1 |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 9V |
| Max Supply Current | 55μA |
| Turn On Delay Time | 193 ns |
| Voltage - Supply, Single/Dual (±) | 9V~40V ±9V~22V |
| Supply Type | Dual, Single |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 207 ns |
| Max Dual Supply Voltage | 22V |
| -3db Bandwidth | 170MHz |
| On-State Resistance (Max) | 7Ohm |
| Min Dual Supply Voltage | 9V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 50 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 21pF 23pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 21ns, 23ns |
| Charge Injection | 275pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 253ns |
| Switch-off Time-Max | 242ns |
| Normal Position | NO |
| Length | 3mm |
| RoHS Status | ROHS3 Compliant |
ADG5401BRMZ-RL7 Overview
This electronic part is conveniently packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), making it easy to ship abroad. High reliability is provided by advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. The operating temperature is extended to around -40°C~125°C TA. There are 8 terminations totally. The electronic part provides high-quality output because it has 1 channels. A 15V voltage supply should turn on and run the electronic component. A SPST - NO switching circuit is used for these analog switches. There are 1 circuits in this multiplexer. ADG5401 can be used to search for analog multiplexer variants. There is 7Ohm internal resistance in this digital multiplexer. For functions related to 8 pins, please refer to the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. It is normally recommended that users do not supply the multiplexer with voltages higher than 40V. A cost-effective Dual, Single supply type analogue multiplexer. The lowest voltage fed to the electronic component should be 9V. Put voltage above 55μA on the multiplexer to cause damage. Despite this switch's dual supply capability, its voltage should not exceed 22V. The voltage should be at least 9V if you are using dual power supplies.
ADG5401BRMZ-RL7 Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 170MHz
ADG5401BRMZ-RL7 Applications
There are a lot of Analog Devices Inc. ADG5401BRMZ-RL7 Analog Switches & Multiplexers ICs applications.
- Channelized and Unchannelized DS3 applications
- Signal routing between systems
- FTTH
- Relay replacements
- High-Voltage
- Video signal routing
- E1 Network Equipment
- Fiber In The Loop (FITL)
- Automotive applications
- Communications systems
