ADG5409BRUZ

165ns, 153ns SP4T 14Ohm DUAL Analog Switches BREAK-BEFORE-MAKE ADG5409 16 Pins 250pA 15V 16-TSSOP (0.173, 4.40mm Width)

Manufacturer: Analog Devices Inc.
Nocochips NO: 84-ADG5409BRUZ
Package: 16-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 822
Description: 165ns, 153ns SP4T 14Ohm DUAL Analog Switches BREAK-BEFORE-MAKE ADG5409 16 Pins 250pA 15V 16-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Lifecycle Status	PRODUCTION (Last Updated: 1 week ago)
Contact Plating	Tin
Mounting Type	Surface Mount
Package / Case	16-TSSOP (0.173, 4.40mm Width)
Surface Mount	YES
Number of Pins	16
Operating Temperature	-40°C~125°C TA
Packaging	Tube
JESD-609 Code	e3
Pbfree Code	no
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
ECCN Code	EAR99
Resistance	14Ohm
Subcategory	Multiplexer or Switches
Max Power Dissipation	2.9mW
Technology	CMOS
Terminal Position	DUAL
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	1
Supply Voltage	15V
Terminal Pitch	0.65mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	ADG5409
Pin Count	16
Number of Channels	1
Interface	Parallel
Number of Circuits	2
Max Supply Voltage	40V
Min Supply Voltage	9V
Analog IC - Other Type	DIFFERENTIAL MULTIPLEXER
Nominal Supply Current	100μA
Power Dissipation	2.9mW
Max Supply Current	80pA
Turn On Delay Time	218 ns
Number of Inputs	8
Voltage - Supply, Single/Dual (±)	9V~40V ±9V~22V
Bandwidth	88MHz
Neg Supply Voltage-Nom (Vsup)	-15V
Turn-Off Delay Time	189 ns
Max Dual Supply Voltage	22V
On-State Resistance (Max)	14Ohm
Min Dual Supply Voltage	9V
High Level Output Current	75mA
Dual Supply Voltage	20V
Multiplexer/Demultiplexer Circuit	4:1
Off-state Isolation-Nom	60 dB
Current - Leakage (IS(off)) (Max)	250pA
Channel Capacitance (CS(off), CD(off))	17pF 48pF
On-state Resistance Match-Nom	0.8Ohm
Switch Circuit	SP4T
Switch Time (Ton, Toff) (Max)	165ns, 153ns
Charge Injection	155pC
Channel-to-Channel Matching (ΔRon)	300m Ω
Crosstalk	-60dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Drain to Source Resistance	22Ohm
Signal Current-Max	0.03A
Height	1.2mm
Length	5.1mm
Width	4.5mm
Radiation Hardening	No
REACH SVHC	No SVHC
RoHS Status	ROHS3 Compliant
Lead Free	Contains Lead

ADG5409BRUZ Overview

The electronic part can be shipped overseas conveniently because it is packaged in 16-TSSOP (0.173, 4.40mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. The multiplexer is located in Surface Mount. Multiplexers and demultiplexers have a number of circuits 4:1. Temperatures around -40°C~125°C TA are extended for operation. In total, there are 16 terminations. A 1 channel electronic part produces high-quality output. Powered by a 15V voltage supply, the electrical part should be switched on and run. Into the electrical component body are injected 16 pins. Circuits based on SP4T switching are used to construct these analog switch ics. A 2 circuit is present in this switch device. Try searching with ADG5409 to find analog multiplexer variants. Analog switches have 14Ohm internal resistance. To find out what the 16 pins do, please refer to the datasheets. Multiplexer or Switches is a typical switch device. In a normalsituation, users should not supply the switches with voltage higher than 40V. 9V is the lowest voltage the electrical component should receive. When the digital multiplexer is charged above 80pA, damage can occur. For this multiplexer, dual supply voltage is feasible, but it should not exceed 22V. In the case of dual power supplies, you should connect at least 9V. This product is integrated with an analog integrated circuit (IC) of type DIFFERENTIAL MULTIPLEXER. Operating 8 inputs is required. 88MHz-bandwidths can be used to transfer data between multiplexers. There is 22Ohm resistance between the Drain and Source on this part.