Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 3 weeks ago) |
Contact Plating |
Tin |
Mounting Type |
Surface Mount |
Package / Case |
16-TSSOP (0.173, 4.40mm Width) |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
14Ohm |
Max Power Dissipation |
2.9mW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
15V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG5409 |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Number of Channels |
4 |
Interface |
Parallel |
Number of Circuits |
2 |
Max Supply Voltage |
40V |
Min Supply Voltage |
9V |
Operating Supply Current |
80μA |
Power Dissipation |
2.9mW |
Max Supply Current |
80pA |
Turn On Delay Time |
218 ns |
Logic Function |
Multiplexer |
Number of Inputs |
8 |
Voltage - Supply, Single/Dual (±) |
9V~40V ±9V~22V |
Supply Type |
Dual, Single |
Bandwidth |
88MHz |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
189 ns |
Max Dual Supply Voltage |
22V |
On-State Resistance (Max) |
14Ohm |
Min Dual Supply Voltage |
9V |
High Level Output Current |
75mA |
Multiplexer/Demultiplexer Circuit |
4:1 |
Off-state Isolation-Nom |
60 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
17pF 48pF |
On-state Resistance Match-Nom |
0.8Ohm |
Switch Circuit |
SP4T |
Switch Time (Ton, Toff) (Max) |
165ns, 153ns |
Charge Injection |
155pC |
Channel-to-Channel Matching (ΔRon) |
300m Ω |
Crosstalk |
-60dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Signal Current-Max |
0.03A |
Length |
5mm |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG5409BRUZ-REEL7 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-TSSOP (0.173, 4.40mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). This analog switch is mounted in Surface Mount. Multiplexers and demultiplexers have the same number of circuits 4:1. Around -40°C~125°C TA is the extended operating temperature. Total terminations are 16. As a result of its 4 channels, this electronic component provides high-quality output. In the case of a voltage supply of 15V volts, the electrical part can be powered up and run. 16 pins are injected to the electronic part body. Unlike digital switches, these are based on SP4T switching circuits. A 2 circuit is present in this switch device. Look for analog switch ic variants by searching with ADG5409. Analog switches have 14Ohm internal resistance. For details about the functions of 16 pins, please refer to the datasheets. Multiplexers should not be powered above 40V in normal situations. The analog switch ic is of the Dual, Single supply type and is cost-effective. 9V is the lowest voltage that should be fed to the electronic electronic part. This digital switch can be operated with a current of 80μA. The analogue multiplexer may be damaged if voltage is greater than 80pA. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 22V. The voltage should be at least 9V if you are using dual power supplies. Among the inputs that can be operated are the 8 inputs. A 88MHz-bandwidth can be used for data transfer.
ADG5409BRUZ-REEL7 Features
4 Channels
Switch Circuit: SP4T
80μA Supply Current
Bandwidth: 88MHz
ADG5409BRUZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG5409BRUZ-REEL7 Analog Switches & Multiplexers ICs applications.
- Low-Voltage
- Channelized and Unchannelized DS3 applications
- ISDN NT1/TA
- Private Branch Exchange (PBX)
- Channel Banks
- Signal routing between systems
- Ultrasound
- PDAs
- SONET
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads