ADG5412BFBCPZ-RL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | 16-WQFN Exposed Pad, CSP |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| Resistance | 11.5Ohm |
| Terminal Finish | Tin (Sn) |
| Terminal Position | QUAD |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG5412 |
| Pin Count | 16 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Interface | Parallel |
| Number of Circuits | 4 |
| Max Supply Voltage | 44V |
| Min Supply Voltage | 8V |
| Test Frequency | 1MHz |
| Power Dissipation | 1mW |
| Voltage - Supply, Single/Dual (±) | 8V~44V ±5V~22V |
| Bandwidth | 160MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Max Dual Supply Voltage | 22V |
| -3db Bandwidth | 270MHz |
| On-State Resistance (Max) | 11.5Ohm |
| Min Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 12pF 11pF |
| On-state Resistance Match-Nom | 0.05Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 500ns, 515ns |
| Insertion Loss (dB) | -0.6 dB |
| Charge Injection | -640pC |
| Channel-to-Channel Matching (ΔRon) | 50m Ω |
| Crosstalk | -90dB @ 1MHz |
| Height Seated (Max) | 0.8mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
ADG5412BFBCPZ-RL7 Overview
Due to its 16-WQFN Exposed Pad, CSP packaging, the electronic part is convenient for international shipping. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). In Surface Mount, you'll find this switch device. 1:1 is the ratio between multiplexers and demultiplexers. The operating temperature is extended to around -40°C~125°C TA. In total, there have been 16 terminations. This electronic part offers high-quality output due to its 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. This electronic part can be found in the 16 series. On the other hand, analog switches can be constructed using SPST - NO switching circuits. The multiplexer consists of 4 circuits. Try searching for the analog switch ic with ADG5412 if you are looking for variants. The internal resistance of this digital multiplexer is 11.5Ohm. Please refer to the datasheets for 16 pins functions. An abnormal situation would be for the switch device to be supplied with a voltage greater than 44V. 8V is the lowest voltage the electrical component should receive. If put voltage greater than 22V on the multiplexer, damage may be caused to the device. With dual power supplies, you should attach at least 5V. A 160MHz-bandwidth can be used for data transfer.
ADG5412BFBCPZ-RL7 Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 270MHz
Bandwidth: 160MHz
ADG5412BFBCPZ-RL7 Applications
There are a lot of Analog Devices Inc. ADG5412BFBCPZ-RL7 Analog Switches & Multiplexers ICs applications.
- High speed data transmission line cards
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Ultrasound
- Transmit
- Digital access cross connects
- Microwave transmission systems
- 65 V DACs
- Audio and video signal routing
- Cellular phones
- Video signal routing
