Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 3 months ago) |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
16-TSSOP (0.173, 4.40mm Width) |
Number of Pins |
16 |
Weight |
172.98879mg |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tube |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
Resistance |
11.5Ohm |
Terminal Finish |
Matte Tin (Sn) |
Max Power Dissipation |
1mW |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
4 |
Supply Voltage |
15V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG5412 |
Pin Count |
16 |
Polarity |
Non-Inverting |
Number of Channels |
1 |
Interface |
Parallel |
Number of Circuits |
4 |
Max Supply Voltage |
40V |
Min Supply Voltage |
9V |
Test Frequency |
1MHz |
Power Dissipation |
1mW |
Max Supply Current |
55μA |
Turn On Delay Time |
202 ns |
Voltage - Supply, Single/Dual (±) |
8V~44V ±5V~22V |
Supply Type |
Dual, Single |
Bandwidth |
160MHz |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
145 ns |
Max Dual Supply Voltage |
22V |
-3db Bandwidth |
270MHz |
On-State Resistance (Max) |
11.5Ohm |
Min Dual Supply Voltage |
9V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
12pF 11pF |
On-state Resistance Match-Nom |
0.05Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
500ns, 515ns |
Insertion Loss (dB) |
-0.6 dB |
Charge Injection |
-640pC |
Channel-to-Channel Matching (ΔRon) |
50m Ω |
Crosstalk |
-90dB @ 1MHz |
Height |
1.05mm |
Length |
5.1mm |
Width |
4.5mm |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG5412BFBRUZ Overview
Due to its 16-TSSOP (0.173, 4.40mm Width) packaging, the electronic part is convenient for international shipping. This packaging method provides high reliability because it uses advanced packaging techniques. In Surface Mount, this analog switch is mounted. 1:1 is the ratio between multiplexers and demultiplexers. The operating temperature is extended to around -40°C~125°C TA. In total, there are 16 terminations. The electronic part delivers high-quality output through its 1 channels. Powered by a 15V voltage supply, the electrical part should be switched on and run. An injection of 16 pins is performed into the body of the electrical component. A SPST - NO switching circuit is used to build these analog multiplexers. A total of 4 circuits make up this switch device. ADG5412 can be used to search for analog multiplexer variants. An switch multiplexer with 11.5Ohm internal resistance has a value of 11.5Ohm. The datasheets for the 16 pins explain the functions. normally, users should not supply switches with voltages higher than 40V. Digital switch that provides Dual, Single power at a cost-effective price. It is recommended that the electrical component receives a voltage of 9V. Put voltage above 55μA on the multiplexer to cause damage. Despite this switch device's dual supply capability, its voltage should not exceed 22V. If you are using dual power supplies, you should attach at least 9V. It is possible to transfer data over a 160MHz-bandwidth.
ADG5412BFBRUZ Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 270MHz
Bandwidth: 160MHz
ADG5412BFBRUZ Applications
There are a lot of Analog Devices Inc. ADG5412BFBRUZ Analog Switches & Multiplexers ICs applications.
- Relay Replacement
- SONET
- Fiber In The Loop (FITL)
- 65 V DACs
- Relay replacements
- Digital cross connects (DSX-1)
- Medical
- Isolation
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- E1 Multiplexer