ADG5413BRUZ-REEL7
| Parameters | |
|---|---|
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 months ago) |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 10Ohm |
| Terminal Finish | MATTE TIN |
| Additional Feature | 2 SWITCHES WITH INVERTED LOGIC |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 1mW |
| Technology | CMOS |
| Terminal Form | NO LEAD |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 15V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADG5413 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 40V |
| Min Supply Voltage | 9V |
| Test Frequency | 1MHz |
| Operating Supply Current | 80μA |
| Power Dissipation | 1mW |
| Max Supply Current | 55μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 202 ns |
| Number of Inputs | 4 |
| Voltage - Supply, Single/Dual (±) | 9V~40V ±9V~22V |
| Supply Type | Dual, Single |
| Bandwidth | 160MHz |
| Neg Supply Voltage-Nom (Vsup) | -15V |
| Turn-Off Delay Time | 145 ns |
| Max Dual Supply Voltage | 22V |
| On-State Resistance (Max) | 10Ohm |
| Min Dual Supply Voltage | 9V |
| Dual Supply Voltage | 15V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 78 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 17pF 17pF |
| On-state Resistance Match-Nom | 0.35Ohm |
| Switch Circuit | SPST - NO/NC |
| Switch Time (Ton, Toff) (Max) | 187ns, 138ns |
| Insertion Loss (dB) | -0.6 dB |
| Charge Injection | 310pC |
| Channel-to-Channel Matching (ΔRon) | 1.5 Ω |
| Crosstalk | -70dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 262ns |
| Switch-off Time-Max | 182ns |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG5413BRUZ-REEL7 Overview
Shipping overseas is convenient with the electronic component packed in 16-TSSOP (0.173, 4.40mm Width). High reliability is ensured by the advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. Multiplexer and demultiplexer circuits have a number 1:1. Operational temperature extended around -40°C~125°C TA. In total, there have been 16 terminations. A 1 channel electronic part produces high-quality output. When the electronic component is given a voltage of 15V, it should be turned on and run. An electrical component of this type can be found in the 16 series. Circuits based on SPST - NO/NC switching are used to construct these analog switch ics. Try searching with ADG5413 to find analog multiplexer variants. An switch multiplexer with 10Ohm internal resistance has a value of 10Ohm. For functions related to 16 pins, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. A voltage higher than 40V should not normally be supplied to the switches. Analog switch ics with Dual, Single supply type are cost-effective. In order for the electronic part to function properly, the lowest voltage should be 9V. In order to operate this switch device, it would need a current of 80μA. Put voltage above 55μA on the multiplexer to cause damage. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 22V. The voltage should be at least 9V if you are using dual power supplies. There are SEPARATE OUTPUT outputs on this analog switch ic. Operating the 4 inputs requires 4 inputs. In 160MHz-bandwidths, data can be transferred. Don't miss this electronic component's additional features, such as: 2 SWITCHES WITH INVERTED LOGIC.
ADG5413BRUZ-REEL7 Features
1 Channels
Switch Circuit: SPST - NO/NC
80μA Supply Current
Bandwidth: 160MHz
Additional Features: 2 SWITCHES WITH INVERTED LOGIC
ADG5413BRUZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG5413BRUZ-REEL7 Analog Switches & Multiplexers ICs applications.
- Automatic test equipment
- Multi-Line E1 Interface Cards
- Digital cross connects (DSX-1)
- Fault Tolerant Systems
- Communication systems
- Data switching
- Imaging
- FTTH
- DVD-R
- High reliability control systems
