Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 1 month ago) |
Mounting Type |
Surface Mount |
Package / Case |
8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
Surface Mount |
YES |
Number of Pins |
8 |
Weight |
139.989945mg |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Resistance |
14Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Form |
GULL WING |
Number of Functions |
1 |
Supply Voltage |
15V |
Terminal Pitch |
0.65mm |
Base Part Number |
ADG5419 |
Pin Count |
8 |
Number of Outputs |
2 |
Number of Channels |
1 |
Interface |
Parallel |
Max Supply Voltage |
40V |
Min Supply Voltage |
9V |
Test Frequency |
1MHz |
Operating Supply Current |
80μA |
Max Supply Current |
55μA |
Turn On Delay Time |
260 ns |
Number of Inputs |
1 |
Voltage - Supply, Single/Dual (±) |
9V~40V ±9V~22V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
260 ns |
Max Dual Supply Voltage |
22V |
-3db Bandwidth |
190MHz |
On-State Resistance (Max) |
14Ohm |
Min Dual Supply Voltage |
9V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
60 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
11pF 22pF |
On-state Resistance Match-Nom |
0.1Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
239ns, 185ns |
Insertion Loss (dB) |
-0.7 dB |
Charge Injection |
160pC |
Channel-to-Channel Matching (ΔRon) |
100m Ω |
Crosstalk |
-80dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Drain to Source Resistance |
23Ohm |
Length |
3mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG5419BRMZ-RL7 Overview
Presented in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), this electrical component is convenient for overseas shipping. The advanced packaging method Tape & Reel (TR) provides high reliability. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have a number of circuits 2:1. Increasing operating temperature to around -40°C~125°C TA. In total, there are 8 terminations. This electronic part offers high-quality output due to its 1 channels. If the voltage supply is 15V volts, the electrical component should be turned on and run. It is part of the design of the 8 series that this electronic component is included. On the other hand, analog switches can be constructed using SPDT switching circuits. Try searching for the analog switch ic with ADG5419 if you are looking for variants. A 14Ohm internal resistance characterizes this multiplexer. Please refer to the datasheets for 8 pins functions. This switch device is a typical Multiplexer or Switches. Users shouldn't supply more than 40V voltage to the switch device. The analog switch ic is of the Dual, Single supply type and is cost-effective. It is recommended to use 9V as the lowest voltage for the electrical part. 80μA current would be enough for this multiplexer to operate. If put voltage greater than 55μA on the device, damage may be caused to the analogue multiplexer. There is no problem with using dual supply voltage, but it should not exceed 22V. In the case of dual power supplies, you should connect at least 9V. Operating the 1 inputs requires 1 inputs. A Drain to Source resistance of 23Ohm is shown for this electronic part. In this digital multiplexer, there are 2 outputs.
ADG5419BRMZ-RL7 Features
1 Channels
Switch Circuit: SPDT
80μA Supply Current
-3db Bandwidth: 190MHz
Drain-to-Source resistance: 23Ohm
ADG5419BRMZ-RL7 Applications
There are a lot of Analog Devices Inc. ADG5419BRMZ-RL7 Analog Switches & Multiplexers ICs applications.
- Low-Voltage
- Communication systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- PDAs
- Residential Gateways, Home Gateway/Router
- Audio/video switches
- Digital access cross connects
- Fiber In The Loop (FITL)
- High reliability control systems
- Relay replacements