Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 1 month ago) |
Contact Plating |
Tin |
Mount |
Surface Mount |
Mounting Type |
Surface Mount |
Package / Case |
10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
Number of Pins |
10 |
Weight |
143.193441mg |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tube |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
10 |
ECCN Code |
EAR99 |
Resistance |
14Ohm |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
15V |
Terminal Pitch |
0.5mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG5423 |
Output |
SEPARATE OUTPUT |
Pin Count |
10 |
Qualification Status |
Not Qualified |
Polarity |
Non-Inverting |
Number of Channels |
1 |
Max Supply Voltage |
40V |
Min Supply Voltage |
9V |
Test Frequency |
1MHz |
Max Supply Current |
55μA |
Turn On Delay Time |
220 ns |
Number of Inputs |
2 |
Voltage - Supply, Single/Dual (±) |
9V~40V ±9V~22V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-15V |
Turn-Off Delay Time |
196 ns |
Max Dual Supply Voltage |
22V |
-3db Bandwidth |
250MHz |
On-State Resistance (Max) |
14Ohm |
Min Dual Supply Voltage |
9V |
Dual Supply Voltage |
15V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
11pF 12pF |
On-state Resistance Match-Nom |
0.1Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
199ns, 184ns |
Insertion Loss (dB) |
0.8 dB |
Charge Injection |
120pC |
Channel-to-Channel Matching (ΔRon) |
100m Ω |
Crosstalk |
-85dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
370ns |
Normal Position |
NO/NC |
Height |
950μm |
Length |
3.1mm |
Width |
3.1mm |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG5423BRMZ Overview
Shipping overseas is convenient with the electronic component packed in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). Advanced packaging method Tube is used to provide high reliability. Surface Mount is where this multiplexer is located. Multiplexer and demultiplexer circuits have a number 1:1. Temperatures around -40°C~125°C TA are extended for operation. In total, there are 10 terminations. A 1 channel electronic part produces high-quality output. With a 15V voltage supply, the electrical component should be turned on and run. Electronic part bodies are injected with 10 pins. A SPST - NO switching circuit is used to build these analog multiplexers. If you are looking for variants of the digital switch, trying search with ADG5423. The internal resistance of this digital multiplexer is 14Ohm. The datasheets for the 10 pins explain the functions. There is Multiplexer or Switches analog multiplexer like this in the world. It is normally recommended that users do not supply the multiplexer with voltages higher than 40V. Digital switch that provides Dual, Single power at a cost-effective price. The lowest voltage the electronic part should receive is 9V. If you put voltage higher than 55μA on the digital multiplexer, damage may occur. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 22V. The voltage should be at least 9V if you are using dual power supplies. SEPARATE OUTPUT outputs are utilized by this digital multiplexer. It is possible to operate 2 inputs.
ADG5423BRMZ Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 250MHz
ADG5423BRMZ Applications
There are a lot of Analog Devices Inc. ADG5423BRMZ Analog Switches & Multiplexers ICs applications.
- Communications systems
- Channel Banks
- PDH Multiplexers
- Signal routing between systems
- Low-Voltage
- SONET
- Relay replacements
- Multi-Line E1 Interface Cards
- Sample-and-hold systems
- Fiber In The Loop (FITL)