Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 3 weeks ago) |
Mounting Type |
Surface Mount |
Package / Case |
8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
Surface Mount |
YES |
Number of Pins |
8 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Resistance |
2.5Ohm |
Terminal Finish |
Matte Tin (Sn) |
Additional Feature |
CAN ALSO OPERATE WITH 2.7V TO 5.5V SINGLE SUPPLY |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
10μW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
5V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG602 |
Pin Count |
8 |
Qualification Status |
Not Qualified |
Number of Channels |
1 |
Interface |
Parallel |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
2.7V |
Operating Supply Current |
1nA |
Power Dissipation |
10μW |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
120 ns |
Voltage - Supply, Single/Dual (±) |
2.7V~5.5V ±2.7V~5.5V |
Supply Type |
Dual, Single |
Bandwidth |
180MHz |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
75 ns |
Max Dual Supply Voltage |
5.5V |
On-State Resistance (Max) |
2.5Ohm |
Min Dual Supply Voltage |
2.7V |
Dual Supply Voltage |
5V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
60 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
50pF 50pF |
On-state Resistance Match-Nom |
0.35Ohm |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
120ns, 75ns |
Charge Injection |
250pC |
Switching |
BREAK-BEFORE-MAKE |
Normal Position |
NC |
Length |
3mm |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG602BRMZ-REEL7 Overview
Shipping overseas is convenient with the electronic component packed in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). Advanced packaging method Tape & Reel (TR) is used to provide high reliability. Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have a ratio of 1:1. Operational temperature extended around -40°C~85°C TA. 8 terminations have been made so far. High-quality output is provided by the electronic component's 1 channels. When the electronic component is given a voltage of 5V, it should be turned on and run. An injection of 8 pins is performed into the body of the electrical component. These analog multiplexers are built based on SPST - NC switching circuits. Try searching for ADG602 variants of the analog switch ic. Analog switches have 2.5Ohm internal resistance. Please refer to the datasheets for 8 pins functions. The analog multiplexer shown here is a typical Multiplexer or Switches. Users shouldn't supply more than 5.5V voltage to the switch device. The digital multiplexer has a low cost Dual, Single supply. 2.7V is the lowest voltage the electrical component should receive. For this digital switch to work, 1nA current would suffice. Put voltage above 1μA on the multiplexer to cause damage. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 5.5V. With dual power supplies, you should attach at least 2.7V. This switch operates within the bandwidth of 180MHz. There is also CAN ALSO OPERATE WITH 2.7V TO 5.5V SINGLE SUPPLY to look out for in this electronic part.
ADG602BRMZ-REEL7 Features
1 Channels
Switch Circuit: SPST - NC
1nA Supply Current
Bandwidth: 180MHz
Additional Features: CAN ALSO OPERATE WITH 2.7V TO 5.5V SINGLE SUPPLY
ADG602BRMZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG602BRMZ-REEL7 Analog Switches & Multiplexers ICs applications.
- Channel Banks
- Remote Powered Equipment
- Access Concentrators
- Switching Systems
- Audio/video switches
- PCMCIA cards
- ISDN NT1/TA
- Relay Replacement
- Channelized and Unchannelized DS3 applications
- Communications systems