ADG608TRU
| Parameters | |
|---|---|
| Peak Reflow Temperature (Cel) | 235 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | ADG608 |
| Pin Count | 16 |
| Operating Supply Voltage | 5V |
| Number of Channels | 8 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 6.5V |
| Min Supply Voltage | 3V |
| Analog IC - Other Type | SINGLE-ENDED MULTIPLEXER |
| Operating Supply Current | 50nA |
| Power Dissipation | 1.5μW |
| Throw Configuration | DPST |
| Propagation Delay | 75 ns |
| Turn On Delay Time | 100 ns |
| Number of Inputs | 8 |
| Voltage - Supply, Single/Dual (±) | 3.3V~5V ±5V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 50 ns |
| Max Dual Supply Voltage | 6.5V |
| On-State Resistance (Max) | 30Ohm |
| High Level Output Current | 20mA |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 8:1 |
| Off-state Isolation-Nom | 85 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 40pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Time (Ton, Toff) (Max) | 75ns, 45ns |
| Charge Injection | 6pC |
| Channel-to-Channel Matching (ΔRon) | 5 Ω (Max) |
| Crosstalk | -85dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Signal Current-Max | 0.02A |
| Length | 5mm |
| Width | 4.4mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
| Contact Plating | Lead, Tin |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -55°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 30Ohm |
| Additional Feature | OPERATION WITH SINGLE 3V/5V ALSO POSSIBLE |
| Subcategory | Multiplexer or Switches |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
ADG608TRU Overview
Packed in 16-TSSOP (0.173, 4.40mm Width), the electronic component is convenient for shipping overseas. This packaging method provides high reliability because it uses advanced packaging techniques. This analog switch is mounted in Surface Mount. 8:1 is the ratio between multiplexers and demultiplexers. Operational temperature extended around -55°C~125°C TA. There are 16 terminations totally. As a result of its 8 channels, this electronic component provides high-quality output. When the electronic component is given a voltage of 5V, it should be turned on and run. It is injected into the electrical part body with 16 pins. Circuits number 1 make up this analogue multiplexer. Try searching with ADG608 if you're looking for variants. Analog switches have 30Ohm internal resistance. For details about the functions of 16 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. Users should never supply a voltage higher than 6.5V to a switch device. In order for the electronic part to function properly, the lowest voltage should be 3V. It would be sufficient to run this analogue multiplexer with 50nA current. For this switch, a dual supply voltage is feasible, but it must not exceed 6.5VIt is integrated with a SINGLE-ENDED MULTIPLEXER analog IC. 5V operating voltages can be used with this electrical part. The 8 inputs need to be operated in order to work. Additional features of the electronic component include: OPERATION WITH SINGLE 3V/5V ALSO POSSIBLE.
ADG608TRU Features
8 Channels
50nA Supply Current
Additional Features: OPERATION WITH SINGLE 3V/5V ALSO POSSIBLE
ADG608TRU Applications
There are a lot of Analog Devices Inc. ADG608TRU Analog Switches & Multiplexers ICs applications.
- Signal routing between systems
- DSUs
- Wireless Local Loop
- Routers
- CSU
- Private Branch Exchange (PBX)
- PCMCIA cards
- DVD-R
- PBX interfaces
- Cross Connects
