Parameters |
Mounting Type |
Surface Mount |
Package / Case |
16-TSSOP (0.173, 4.40mm Width) |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
-55°C~125°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
30Ohm |
Additional Feature |
OPERATION WITH SINGLE 3V/5V ALSO POSSIBLE |
Technology |
BICMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
235 |
Number of Functions |
1 |
Supply Voltage |
5V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
20 |
Base Part Number |
ADG608 |
Pin Count |
16 |
Operating Supply Voltage |
5V |
Number of Channels |
8 |
Interface |
Parallel |
Number of Circuits |
1 |
Max Supply Voltage |
6.5V |
Operating Supply Current |
50nA |
Power Dissipation |
1.5μW |
Throw Configuration |
DPST |
Propagation Delay |
75 ns |
Turn On Delay Time |
170 ns |
Logic Function |
Multiplexer |
Voltage - Supply, Single/Dual (±) |
3.3V~5V ±5V |
Supply Type |
Dual, Single |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
60 ns |
Max Dual Supply Voltage |
6.5V |
On-State Resistance (Max) |
30Ohm |
Dual Supply Voltage |
5V |
Multiplexer/Demultiplexer Circuit |
8:1 |
Off-state Isolation-Nom |
85 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
9pF 40pF |
On-state Resistance Match-Nom |
2Ohm |
Switch Time (Ton, Toff) (Max) |
75ns, 45ns |
Charge Injection |
6pC |
Channel-to-Channel Matching (ΔRon) |
5 Ω (Max) |
Crosstalk |
-85dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Signal Current-Max |
0.02A |
Length |
5mm |
Width |
4.4mm |
Radiation Hardening |
No |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
ADG608TRU-REEL7 Overview
Presented in 16-TSSOP (0.173, 4.40mm Width), this electrical component is convenient for overseas shipping. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. In Surface Mount, you'll find this switch device. 8:1 is the ratio between multiplexers and demultiplexers. Operating temperature extended to -55°C~125°C TA. In total, there are 16 terminations. A electrical component with 8 channels is capable of high-quality output. If the voltage supply is 5V volts, the electrical component should be turned on and run. As part of the design of the 16 series, this electronic part has been incorporated into the system. Circuits number 1 make up this analogue multiplexer. Try searching for ADG608 variants of the analog switch ic. An switch multiplexer with 30Ohm internal resistance has a value of 30Ohm. You can find the functions of the 16 pins in the datasheets. normally, users should not supply switches with voltages higher than 6.5V. Analog switch ics with Dual, Single supply type are cost-effective. This multiplexer would work with 50nA current. There is no problem with using dual supply voltage, but it should not exceed 6.5V. A voltage of 5V can be used to operate the electronic component. Additional features include: OPERATION WITH SINGLE 3V/5V ALSO POSSIBLE.
ADG608TRU-REEL7 Features
8 Channels
50nA Supply Current
Additional Features: OPERATION WITH SINGLE 3V/5V ALSO POSSIBLE
ADG608TRU-REEL7 Applications
There are a lot of Analog Devices Inc. ADG608TRU-REEL7 Analog Switches & Multiplexers ICs applications.
- Video signal routing
- Microprocessor Controlled Analog Systems
- Medical Instrumentation
- Transmit
- Data Acquisition Systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- SDH/SONET multiplexers
- DSLAMs
- RGB switches
- Communications systems