ADG609BRU-REEL7
| Parameters | |
|---|---|
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 30Ohm |
| Additional Feature | OPERATION WITH SINGLE 3V/5V ALSO POSSIBLE |
| Subcategory | Multiplexer or Switches |
| Technology | BICMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG609 |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 4 |
| Number of Circuits | 2 |
| Max Supply Voltage | 6.5V |
| Analog IC - Other Type | DIFFERENTIAL MULTIPLEXER |
| Throw Configuration | 4PST |
| Number of Inputs | 8 |
| Voltage - Supply, Single/Dual (±) | 3.3V~5V ±5V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Max Dual Supply Voltage | 6.5V |
| On-State Resistance (Max) | 30Ohm |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 4:1 |
| Off-state Isolation-Nom | 85 dB |
| Current - Leakage (IS(off)) (Max) | 500pA |
| Channel Capacitance (CS(off), CD(off)) | 9pF 20pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SP4T |
| Switch Time (Ton, Toff) (Max) | 75ns, 45ns |
| Charge Injection | 6pC |
| Channel-to-Channel Matching (ΔRon) | 5 Ω (Max) |
| Crosstalk | -85dB @ 100kHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 75ns |
| Switch-off Time-Max | 75ns |
| Length | 5mm |
| Width | 4.4mm |
| RoHS Status | Non-RoHS Compliant |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
ADG609BRU-REEL7 Overview
The electronic component is convenient to ship overseas because it is packed in a 16-TSSOP (0.173, 4.40mm Width). To ensure high reliability, a new packaging method Tape & Reel (TR) is used. There is an analog multiplexer mounted in position Surface Mount. Multiplexers and demultiplexers have a ratio of 4:1. Operating temperature extended to -40°C~85°C TA. In total, 16 terminations have occurred. Due to its 4 channels, the electrical component produces high-quality output. With a 5V voltage supply, the electrical component should be turned on and run. It is injected into the electrical part body with 16 pins. The analog switch ics are built using SP4T switching circuits. This multiplexer is composed of 2 circuits. Try searching for the analog switch ic with ADG609 if you are looking for variants. An switch multiplexer with 30Ohm internal resistance has a value of 30Ohm. For details about the functions of 16 pins, please refer to the datasheets. Multiplexer or Switches is a typical switch device. In normalcircumstances, users should not exceed 6.5V volts for the multiplexer. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 6.5V. An analog IC with the number DIFFERENTIAL MULTIPLEXER is integrated into this board. The electrical component supports 8 inputs. Additional features include: OPERATION WITH SINGLE 3V/5V ALSO POSSIBLE.
ADG609BRU-REEL7 Features
4 Channels
Switch Circuit: SP4T
Additional Features: OPERATION WITH SINGLE 3V/5V ALSO POSSIBLE
ADG609BRU-REEL7 Applications
There are a lot of Analog Devices Inc. ADG609BRU-REEL7 Analog Switches & Multiplexers ICs applications.
- ISDN NT1/TA
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Relay replacements
- Ultrasound
- Public switching systems
- Digital cross connects (DSX-1)
- Power routing
- Data switching
- Cable PC
- Battery Powered Instruments
