Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 2 weeks ago) |
Mounting Type |
Surface Mount |
Package / Case |
16-TSSOP (0.173, 4.40mm Width) |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
22Ohm |
Terminal Finish |
Matte Tin (Sn) |
Additional Feature |
OPERATION WITH SINGLE 3V/5V ALSO POSSIBLE |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
1.5μW |
Technology |
BICMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
5V |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG609 |
Pin Count |
16 |
Operating Supply Voltage |
5V |
Number of Channels |
4 |
Interface |
Parallel |
Number of Circuits |
2 |
Max Supply Voltage |
6.5V |
Min Supply Voltage |
3V |
Analog IC - Other Type |
DIFFERENTIAL MULTIPLEXER |
Operating Supply Current |
50nA |
Nominal Supply Current |
50nA |
Power Dissipation |
1.5μW |
Max Supply Current |
200nA |
Throw Configuration |
4PST |
Propagation Delay |
75 ns |
Turn On Delay Time |
170 ns |
Number of Inputs |
8 |
Voltage - Supply, Single/Dual (±) |
3.3V~5V ±5V |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
30 ns |
Max Dual Supply Voltage |
6.5V |
On-State Resistance (Max) |
30Ohm |
High Level Output Current |
20mA |
Dual Supply Voltage |
5V |
Multiplexer/Demultiplexer Circuit |
4:1 |
Off-state Isolation-Nom |
85 dB |
Current - Leakage (IS(off)) (Max) |
500pA |
Channel Capacitance (CS(off), CD(off)) |
9pF 20pF |
On-state Resistance Match-Nom |
2Ohm |
Switch Circuit |
SP4T |
Switch Time (Ton, Toff) (Max) |
75ns, 45ns |
Charge Injection |
6pC |
Channel-to-Channel Matching (ΔRon) |
5 Ω (Max) |
Crosstalk |
-85dB @ 100kHz |
Switching |
BREAK-BEFORE-MAKE |
Drain to Source Resistance |
22Ohm |
Height |
1.05mm |
Length |
5mm |
Width |
4.4mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG609BRUZ Overview
The electronic component is convenient to ship overseas because it is packed in a 16-TSSOP (0.173, 4.40mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tube. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 4:1. Temperatures around -40°C~85°C TA are extended for operation. Total terminations are 16. As a result of its 4 channels, this electronic component provides high-quality output. When a voltage supply of 5V is used, the electronic component should be turned on and run. This electronic part can be found in the 16 series. SP4T switching circuits are used in these analog switch ics. 2 circuits are used in this analogue multiplexer. Try searching with ADG609 if you're looking for variants. There is 22Ohm internal resistance in this digital multiplexer. Please refer to the datasheets for 16 pins functions. In this analog multiplexer, the value is Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 6.5V to the switch device in normal circumstances. It is recommended to use 3V as the lowest voltage for the electrical part. 50nA current would be enough for this multiplexer to operate. The analogue multiplexer may be damaged if voltage is greater than 200nA. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 6.5V. A DIFFERENTIAL MULTIPLEXER analog IC is integrated into the board. The electrical part can be operated at 5V voltage levels. The electrical component supports 8 inputs. There is also OPERATION WITH SINGLE 3V/5V ALSO POSSIBLE to look out for in this electronic part. There is 22Ohm resistance between the Drain and Source on this part.
ADG609BRUZ Features
4 Channels
Switch Circuit: SP4T
50nA Supply Current
Additional Features: OPERATION WITH SINGLE 3V/5V ALSO POSSIBLE
Drain-to-Source resistance: 22Ohm
ADG609BRUZ Applications
There are a lot of Analog Devices Inc. ADG609BRUZ Analog Switches & Multiplexers ICs applications.
- E1 Multiplexer
- Battery-powered systems
- Signal routing between systems
- Video switching
- Microwave transmission systems
- T1/E1 Terminals
- Communication systems
- DSLAMs
- Mechanical reed relay replacement
- Low-Voltage