ADG611YRUZ-REEL
| Parameters | |
|---|---|
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 4 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADG611 |
| Output | SEPARATE OUTPUT |
| Pin Count | 16 |
| Qualification Status | Not Qualified |
| Number of Channels | 4 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2.7V |
| Throw Configuration | SPST |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V ±2.7V~5.5V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Max Dual Supply Voltage | 5.5V |
| -3db Bandwidth | 680MHz |
| On-State Resistance (Max) | 115Ohm |
| Min Dual Supply Voltage | 2.7V |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 5pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 65ns, 40ns |
| Charge Injection | -0.5pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -90dB @ 10MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 90ns |
| Switch-off Time-Max | 50ns |
| Normal Position | NC |
| Height Seated (Max) | 1.2mm |
| Length | 5mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
| Mounting Type | Surface Mount |
| Package / Case | 16-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 16 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 16 |
| ECCN Code | EAR99 |
| Resistance | 115Ohm |
| Terminal Finish | Matte Tin (Sn) |
ADG611YRUZ-REEL Overview
As the electronic part is packed in 16-TSSOP (0.173, 4.40mm Width), international shipping is convenient. To ensure high reliability, a new packaging method Tape & Reel (TR) is used. Multiplexers like this are mounted in the Surface Mount position. In the multiplexer and demultiplexer, 1:1 represents the number of circuits. Operating temperature around -40°C~125°C TA extended. In total, there have been 16 terminations. High-quality output is provided by the electronic component's 4 channels. If the voltage supply is 5V volts, the electrical component should be turned on and run. 16 pins are injected to the electronic part body. Circuits based on SPST - NC switching are used to construct these analog switch ics. Try searching with ADG611 to find analog multiplexer variants. A 115Ohm internal resistance characterizes this multiplexer. Datasheets for functions of 16 pins are available. Theswitch device is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. The lowest voltage fed to the electronic component should be 2.7V. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 5.5V. In the case of dual power supplies, you should connect at least 2.7V. The digital multiplexer has SEPARATE OUTPUT outputs that can be used.
ADG611YRUZ-REEL Features
4 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 680MHz
ADG611YRUZ-REEL Applications
There are a lot of Analog Devices Inc. ADG611YRUZ-REEL Analog Switches & Multiplexers ICs applications.
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Channel Banks
- Microprocessor Controlled Analog Systems
- Precision instrumentation
- SONET/SDH ADM
- Sample-and-hold systems
- Medical
- Channelized and Unchannelized DS3 applications
- Optical Applications
- Audio and video routing
