ADG612YRUZ

65ns, 40ns SPST - NO 115Ohm Analog Switches BREAK-BEFORE-MAKE ADG612 16 Pins 100pA 5V 16-TSSOP (0.173, 4.40mm Width)

Manufacturer: Analog Devices Inc.
Nocochips NO: 84-ADG612YRUZ
Package: 16-TSSOP (0.173, 4.40mm Width)
Datasheet: PDF
Stock: 309
Description: 65ns, 40ns SPST - NO 115Ohm Analog Switches BREAK-BEFORE-MAKE ADG612 16 Pins 100pA 5V 16-TSSOP (0.173, 4.40mm Width)(Kg)

Details

Tags

Parameters
Factory Lead Time	1 Week
Lifecycle Status	PRODUCTION (Last Updated: 3 weeks ago)
Mounting Type	Surface Mount
Package / Case	16-TSSOP (0.173, 4.40mm Width)
Surface Mount	YES
Number of Pins	16
Operating Temperature	-40°C~125°C TA
Packaging	Tube
JESD-609 Code	e3
Pbfree Code	no
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	16
ECCN Code	EAR99
Resistance	115Ohm
Terminal Finish	Matte Tin (Sn)
Subcategory	Multiplexer or Switches
Max Power Dissipation	10μW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	4
Supply Voltage	5V
Time@Peak Reflow Temperature-Max (s)	40
Base Part Number	ADG612
Pin Count	16
Polarity	Non-Inverting
Number of Channels	4
Interface	Parallel
Max Supply Voltage	5.5V
Min Supply Voltage	2.7V
Operating Supply Current	1nA
Nominal Supply Current	1μA
Power Dissipation	10μW
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	65 ns
Voltage - Supply, Single/Dual (±)	2.7V~5.5V ±2.7V~5.5V
Supply Type	Dual, Single
Bandwidth	680MHz
Neg Supply Voltage-Nom (Vsup)	-5V
Turn-Off Delay Time	40 ns
Max Dual Supply Voltage	5.5V
On-State Resistance (Max)	115Ohm
Min Dual Supply Voltage	2.7V
High Level Output Current	10mA
Dual Supply Voltage	5V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	65 dB
Current - Leakage (IS(off)) (Max)	100pA
Channel Capacitance (CS(off), CD(off))	5pF 5pF
On-state Resistance Match-Nom	2Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	65ns, 40ns
Charge Injection	-0.5pC
Channel-to-Channel Matching (ΔRon)	2 Ω
Crosstalk	-90dB @ 10MHz
Switching	BREAK-BEFORE-MAKE
Switch-on Time-Max	260ns
Drain to Source Resistance	85Ohm
Normal Position	NO
Signal Current-Max	0.01A
Height	1.05mm
Length	5mm
Width	4.4mm
Radiation Hardening	No
REACH SVHC	No SVHC
RoHS Status	ROHS3 Compliant
Lead Free	Contains Lead

ADG612YRUZ Overview

Shipping overseas is convenient with the electronic component packed in 16-TSSOP (0.173, 4.40mm Width). The advanced packaging method Tube provides high reliability. A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Operational temperature extended around -40°C~125°C TA. Total terminations are 16. This electronic part offers high-quality output due to its 4 channels. Powered by a 5V voltage supply, the electrical part should be switched on and run. 16 pins are injected to the electronic part body. A SPST - NO switching circuit is used to build these analog multiplexers. If you are looking for variants of the digital switch, trying search with ADG612. The internal resistance of this digital multiplexer is 115Ohm. To find out what the 16 pins do, please refer to the datasheets. Theswitch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. The digital multiplexer has a low cost Dual, Single supply. It is recommended to use 2.7V as the lowest voltage for the electrical part. For this multiplexer to operate, 1nA current would be sufficient. Put voltage above 1μA on the multiplexer to cause damage. There is no problem with using dual supply voltage, but it should not exceed 5.5V. In the case of dual power supplies, you should connect at least 2.7V. There are 680MHz bandwidths for data transfer. This electronic component presents a Drain to Source resistance of 85Ohm.