ADG619BRM
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 6.5Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 10μW |
| Technology | CMOS |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG619 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2.7V |
| Operating Supply Current | 1nA |
| Nominal Supply Current | 1μA |
| Power Dissipation | 10μW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 120 ns |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V ±2.7V~5.5V |
| Supply Type | Dual, Single |
| Bandwidth | 190MHz |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Turn-Off Delay Time | 75 ns |
| Max Dual Supply Voltage | 5.5V |
| On-State Resistance (Max) | 6.5Ohm |
| Min Dual Supply Voltage | 2.7V |
| High Level Output Current | 50mA |
| Dual Supply Voltage | 5V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 67 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 25pF |
| On-state Resistance Match-Nom | 0.7Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 120ns, 75ns |
| Charge Injection | 110pC |
| Channel-to-Channel Matching (ΔRon) | 700m Ω |
| Crosstalk | -67dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Height | 850μm |
| Length | 3mm |
| Width | 3mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG619BRM Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tube. The multiplexer is located in Surface Mount. There is 2:1 ratio between the number of multiplexers and demultiplexers. Around -40°C~85°C TA is the extended operating temperature. Totally, there are 8 terminations. The electronic part delivers high-quality output through its 1 channels. It is safe to turn on and run the electronic component with a 5V voltage supply. An injection of 8 pins is performed into the body of the electrical component. Multiplexers built on a SPDT switching circuit are built. Try searching for ADG619 variants of the analog switch ic. The internal resistance of this digital multiplexer is 6.5Ohm. Please refer to the datasheets for 8 pins functions. There is a standard Multiplexer or Switches analogue multiplexer here. A voltage higher than 5.5V should not normally be supplied to the switches. The analog switch ic is of the Dual, Single supply type and is cost-effective. There should be 2.7V voltage fed to the electrical part below 2.7V. 1nA current would be enough for this multiplexer to operate. When the digital multiplexer is charged above 1μA, damage can occur. For this switch, a dual supply voltage is feasible, but it must not exceed 5.5VA dual power supply should have at least 2.7V voltage attached. The transfer of data can be performed over 190MHz bandwidths. The analog switch ics includes 2 outputs.
ADG619BRM Features
1 Channels
Switch Circuit: SPDT
1nA Supply Current
Bandwidth: 190MHz
ADG619BRM Applications
There are a lot of Analog Devices Inc. ADG619BRM Analog Switches & Multiplexers ICs applications.
- Switching Systems
- Battery Powered Instruments
- Microprocessor controlled systems
- DSUs
- E1 Network Equipment
- High-Voltage
- Optical Applications
- Modems
- Low-Voltage
- DVD-R
