Parameters |
Mounting Type |
Surface Mount |
Package / Case |
8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
Surface Mount |
YES |
Number of Pins |
8 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e0 |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Resistance |
6.5Ohm |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
1 |
Supply Voltage |
5V |
Terminal Pitch |
0.65mm |
Reach Compliance Code |
not_compliant |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG619 |
Pin Count |
8 |
Number of Outputs |
2 |
Qualification Status |
Not Qualified |
Power Supplies |
+-3/+-5V |
Number of Channels |
1 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
2.7V |
Power Dissipation |
10μW |
Voltage - Supply, Single/Dual (±) |
2.7V~5.5V ±2.7V~5.5V |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Max Dual Supply Voltage |
5.5V |
-3db Bandwidth |
190MHz |
On-State Resistance (Max) |
6.5Ohm |
Min Dual Supply Voltage |
2.7V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
67 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
25pF |
On-state Resistance Match-Nom |
0.7Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
120ns, 75ns |
Charge Injection |
110pC |
Channel-to-Channel Matching (ΔRon) |
700m Ω |
Crosstalk |
-67dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-off Time-Max |
75ns |
Length |
3mm |
RoHS Status |
Non-RoHS Compliant |
ADG619BRM-REEL Overview
As the electronic part is packed in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), international shipping is convenient. The advanced packaging method Tape & Reel (TR) provides high reliability. There is an analog multiplexer mounted in position Surface Mount. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. Operation at a temperature around -40°C~85°C TA. Total terminations are 8. By its 1 channels, the electronic component provides high-quality output. With a 5V voltage supply, the electrical component should be turned on and run. An electrical component of this type can be found in the 8 series. Circuits based on SPDT switching are used to construct these analog switch ics. Search with ADG619 if you are looking for analog multiplexer variants. The internal resistance of this digital multiplexer is 6.5Ohm. To find out what the 8 pins do, please refer to the datasheets. Multiplexer or Switches is a typical switch device. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. 2.7V should be the lowest voltage fed to the electronic component. For this multiplexer, dual supply voltage is feasible, but it should not exceed 5.5V. It is recommended that you attach at least 2.7V to your dual power supply. An output of 2 is provided by the digital multiplexer.
ADG619BRM-REEL Features
1 Channels
Switch Circuit: SPDT
-3db Bandwidth: 190MHz
ADG619BRM-REEL Applications
There are a lot of Analog Devices Inc. ADG619BRM-REEL Analog Switches & Multiplexers ICs applications.
- Communication systems
- Avionics test equipment
- Industrial control systems
- Battery-powered systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- New designs requiring multiplexer functions
- Isolation
- 65 V DACs
- Modems
- MP3 players