Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 3 weeks ago) |
Contact Plating |
Tin |
Mounting Type |
Surface Mount |
Package / Case |
8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
Surface Mount |
YES |
Number of Pins |
8 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
8 |
ECCN Code |
EAR99 |
Resistance |
6.5Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
10μW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
5V |
Terminal Pitch |
0.65mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG619 |
Pin Count |
8 |
Number of Outputs |
2 |
Polarity |
Non-Inverting |
Number of Channels |
1 |
Interface |
Parallel |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
2.7V |
Operating Supply Current |
1nA |
Nominal Supply Current |
1μA |
Power Dissipation |
10μW |
Max Supply Current |
1μA |
Turn On Delay Time |
120 ns |
Voltage - Supply, Single/Dual (±) |
2.7V~5.5V ±2.7V~5.5V |
Supply Type |
Dual, Single |
Bandwidth |
190MHz |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
75 ns |
Max Dual Supply Voltage |
5.5V |
On-State Resistance (Max) |
6.5Ohm |
Min Dual Supply Voltage |
2.7V |
High Level Output Current |
50mA |
Dual Supply Voltage |
5V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
67 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
25pF |
On-state Resistance Match-Nom |
0.7Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
120ns, 75ns |
Charge Injection |
110pC |
Channel-to-Channel Matching (ΔRon) |
700m Ω |
Crosstalk |
-67dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Height |
850μm |
Length |
3mm |
Width |
3mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG619BRMZ Overview
Shipping overseas is convenient due to the electrical component's packing in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). High reliability is provided by advanced packaging method Tube. Multiplexers like this are mounted in the Surface Mount position. Multiplexer and demultiplexer circuits have a number 2:1. Operating temperature around -40°C~85°C TA extended. In total, 8 terminations have occurred. A electrical component with 1 channels is capable of high-quality output. Powered by a 5V voltage supply, the electrical part should be switched on and run. A total of 8 pins are injected into the body of the electronic part. Unlike digital switches, these are based on SPDT switching circuits. Try searching for ADG619 variants of the analog switch ic. It has an internal resistance of 6.5Ohm. Datasheets for 8 pin functions are available upon request. This switch device is a typical Multiplexer or Switches. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. Analogue multiplexer with a Dual, Single supply type that is cost-effective. The lowest voltage fed to the electronic component should be 2.7V. An operating current of 1nA would be sufficient for this switch device. A digital multiplexer may suffer damage if voltage is applied above 1μA. Despite this switch device's dual supply capability, its voltage should not exceed 5.5V. A dual power supply should have at least 2.7V voltage attached. 190MHz-bandwidths can be used to transfer data between multiplexers. Multiplexer ics with 2 outputs are available.
ADG619BRMZ Features
1 Channels
Switch Circuit: SPDT
1nA Supply Current
Bandwidth: 190MHz
ADG619BRMZ Applications
There are a lot of Analog Devices Inc. ADG619BRMZ Analog Switches & Multiplexers ICs applications.
- Communication systems
- Relay Replacement
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Audio signal routing
- Public switching systems
- Fiber to the Home
- Sample-and-hold systems
- Optical Applications
- PDH Multiplexers
- Video switching