ADG620BRM-REEL
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 6.5Ohm |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Reach Compliance Code | not_compliant |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG620 |
| Pin Count | 8 |
| Number of Outputs | 2 |
| Qualification Status | Not Qualified |
| Power Supplies | +-3/+-5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2.7V |
| Power Dissipation | 10μW |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V ±2.7V~5.5V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Max Dual Supply Voltage | 5.5V |
| -3db Bandwidth | 190MHz |
| On-State Resistance (Max) | 6.5Ohm |
| Min Dual Supply Voltage | 2.7V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 67 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 25pF |
| On-state Resistance Match-Nom | 0.7Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 65ns, 330ns |
| Charge Injection | 110pC |
| Channel-to-Channel Matching (ΔRon) | 700m Ω |
| Crosstalk | -67dB @ 1MHz |
| Switching | MAKE-BEFORE-BREAK |
| Switch-on Time-Max | 65ns |
| Switch-off Time-Max | 330ns |
| Length | 3mm |
| RoHS Status | Non-RoHS Compliant |
ADG620BRM-REEL Overview
Packed in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width), the electronic component is convenient for shipping overseas. This packaging method provides high reliability because it uses advanced packaging techniques. This analog switch is mounted in Surface Mount. In the multiplexer and demultiplexer, 2:1 represents the number of circuits. Operating temperature around -40°C~85°C TA extended. In total, 8 terminations have occurred. High-quality output is provided by the electronic component's 1 channels. A 5V voltage supply should turn on and run the electronic component. As part of the design of the 8 series, this electronic part has been incorporated into the system. Unlike digital switches, these are based on SPDT switching circuits. ADG620 can be used to search for analog multiplexer variants. As far as internal resistance is concerned, it has 6.5Ohm. To find out what the functions of 8 pins are, please refer to their datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. Multiplexers should not be powered above 5.5V in normal situations. 2.7V is the lowest voltage that should be fed to the electronic electronic part. For this multiplexer, dual supply voltage is feasible, but it should not exceed 5.5V. If you are using dual power supplies, you should attach at least 2.7V. In this digital multiplexer, there are 2 outputs.
ADG620BRM-REEL Features
1 Channels
Switch Circuit: SPDT
-3db Bandwidth: 190MHz
ADG620BRM-REEL Applications
There are a lot of Analog Devices Inc. ADG620BRM-REEL Analog Switches & Multiplexers ICs applications.
- Sample hold systems
- High reliability control systems
- PCMCIA cards
- Cross Connects
- PDH Multiplexers
- Modems
- Power routing
- E1 Network Equipment
- Frame Relay Equipment
- PBX interfaces
