ADG621BRMZ-REEL

120ns, 70ns SPST - NO 5.5Ohm Analog Switches BREAK-BEFORE-MAKE ADG621 10 Pins 250pA 5V 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)

Manufacturer: Analog Devices Inc.
Nocochips NO: 84-ADG621BRMZ-REEL
Package: 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)
Datasheet: PDF
Stock: 888
Description: 120ns, 70ns SPST - NO 5.5Ohm Analog Switches BREAK-BEFORE-MAKE ADG621 10 Pins 250pA 5V 10-TFSOP, 10-MSOP (0.118, 3.00mm Width)(Kg)

Inquiry Now

Details

Tags

Parameters
Factory Lead Time	1 Week
Lifecycle Status	PRODUCTION (Last Updated: 3 weeks ago)
Contact Plating	Tin
Mounting Type	Surface Mount
Package / Case	10-TFSOP, 10-MSOP (0.118, 3.00mm Width)
Surface Mount	YES
Number of Pins	10
Operating Temperature	-40°C~85°C TA
Packaging	Tape & Reel (TR)
JESD-609 Code	e3
Pbfree Code	no
Part Status	Active
Moisture Sensitivity Level (MSL)	1 (Unlimited)
Number of Terminations	10
ECCN Code	EAR99
Resistance	5.5Ohm
Subcategory	Multiplexer or Switches
Max Power Dissipation	10μW
Technology	CMOS
Terminal Form	GULL WING
Peak Reflow Temperature (Cel)	260
Number of Functions	2
Supply Voltage	5V
Terminal Pitch	0.5mm
Time@Peak Reflow Temperature-Max (s)	30
Base Part Number	ADG621
Pin Count	10
Polarity	Non-Inverting
Number of Channels	2
Interface	Parallel
Max Supply Voltage	5.5V
Min Supply Voltage	2.7V
Operating Supply Current	1nA
Nominal Supply Current	1μA
Power Dissipation	10μW
Max Supply Current	1μA
Throw Configuration	SPST
Turn On Delay Time	120 ns
Voltage - Supply, Single/Dual (±)	2.7V~5.5V ±2.7V~5.5V
Supply Type	Dual, Single
Bandwidth	230MHz
Neg Supply Voltage-Nom (Vsup)	-5V
Turn-Off Delay Time	70 ns
Max Dual Supply Voltage	5.5V
On-State Resistance (Max)	5.5Ohm
Min Dual Supply Voltage	2.7V
High Level Output Current	50mA
Dual Supply Voltage	5V
Multiplexer/Demultiplexer Circuit	1:1
Off-state Isolation-Nom	65 dB
Current - Leakage (IS(off)) (Max)	250pA
Channel Capacitance (CS(off), CD(off))	20pF 20pF
On-state Resistance Match-Nom	0.25Ohm
Switch Circuit	SPST - NO
Switch Time (Ton, Toff) (Max)	120ns, 70ns
Charge Injection	110pC
Channel-to-Channel Matching (ΔRon)	250m Ω
Crosstalk	-90dB @ 1MHz
Switching	BREAK-BEFORE-MAKE
Normal Position	NO
Height	950μm
Length	3.1mm
Width	3.1mm
Radiation Hardening	No
RoHS Status	ROHS3 Compliant
Lead Free	Contains Lead

ADG621BRMZ-REEL Overview

The electronic part can be shipped overseas conveniently because it is packaged in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width). This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a ratio of 1:1. Operational temperature extended around -40°C~85°C TA. There are 10 terminations totally. A electrical component with 2 channels is capable of high-quality output. In the case of a voltage supply of 5V volts, the electrical part can be powered up and run. An electrical component like this is included in the 10 series. On the other hand, analog switches can be constructed using SPST - NO switching circuits. Use ADG621 to search for variants of the digital switches. An switch multiplexer with 5.5Ohm internal resistance has a value of 5.5Ohm. For details about the functions of 10 pins, please refer to the datasheets. The analogue multiplexer in this example is a typical Multiplexer or Switches. normally, users should not supply switches with voltages higher than 5.5V. Analog switch ics with Dual, Single supply type are cost-effective. There should be 2.7V voltage fed to the electrical part below 2.7V. The switch device would be able to operate with 1nA current. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. If put voltage greater than 5.5V on the multiplexer, damage may be caused to the device. You should attach at least 2.7V voltage if you are using dual power supply. It is possible to transfer data over a 230MHz-bandwidth.