Parameters |
Mounting Type |
Surface Mount |
Package / Case |
10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
Surface Mount |
YES |
Number of Pins |
10 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tube |
JESD-609 Code |
e3 |
Pbfree Code |
yes |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
10 |
Termination |
SMD/SMT |
ECCN Code |
EAR99 |
Resistance |
5.5Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
2 |
Supply Voltage |
5V |
Terminal Pitch |
0.5mm |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
ADG622 |
Output |
SEPARATE OUTPUT |
Pin Count |
10 |
Operating Supply Voltage |
5V |
Number of Channels |
2 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
2.7V |
Power Dissipation |
10μW |
Throw Configuration |
SPST |
Turn On Delay Time |
75 ns |
Voltage - Supply, Single/Dual (±) |
2.7V~5.5V ±2.7V~5.5V |
Bandwidth |
230MHz |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
45 ns |
Max Dual Supply Voltage |
5.5V |
On-State Resistance (Max) |
5.5Ohm |
Min Dual Supply Voltage |
2.7V |
Dual Supply Voltage |
5V |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
65 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
20pF 20pF |
On-state Resistance Match-Nom |
0.25Ohm |
Switch Circuit |
SPST - NC |
Switch Time (Ton, Toff) (Max) |
120ns, 70ns |
Charge Injection |
110pC |
Channel-to-Channel Matching (ΔRon) |
250m Ω |
Crosstalk |
-90dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-off Time-Max |
70ns |
Normal Position |
NC |
Height |
850μm |
Length |
3mm |
Width |
3mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Lead Free |
ADG622BRMZ Overview
Packed in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width), the electronic component is convenient for shipping overseas. High reliability is provided by advanced packaging method Tube. The multiplexer is located in Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. Operation at a temperature around -40°C~85°C TA. In total, there have been 10 terminations. Due to its 2 channels, the electrical component produces high-quality output. It is safe to turn on and run the electronic component with a 5V voltage supply. A total of 10 pins are injected into the body of the electronic part. Circuits based on SPST - NC switching are used to construct these analog switch ics. Try searching for ADG622 variants of the analog switch ic. An switch multiplexer with 5.5Ohm internal resistance has a value of 5.5Ohm. For details about the functions of 10 pins, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. Multiplexers should not be powered above 5.5V in normal situations. There should be 2.7V voltage fed to the electrical part below 2.7V. For this switch device, it is feasible to have two supplies. However, the voltage should not exceed 5.5V. If you are using dual power supplies, you should attach at least 2.7V. As far as the outputs go, this switch multiplexer utilizes SEPARATE OUTPUT of them. This electrical part is compatible with 5V operating voltages. The transfer of data can be performed over 230MHz bandwidths.
ADG622BRMZ Features
2 Channels
Switch Circuit: SPST - NC
Bandwidth: 230MHz
ADG622BRMZ Applications
There are a lot of Analog Devices Inc. ADG622BRMZ Analog Switches & Multiplexers ICs applications.
- Industrial and process control systems
- High-Voltage
- Microprocessor controlled systems
- ISDN NT1/TA
- Cellular phones
- Industrial control systems
- FTTH
- Cell phones
- Central office
- Existing multiplexer applications (both fault-protected and nonfault-protected)