ADG622BRMZ-REEL
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 10-TFSOP, 10-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 10 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 10 |
| ECCN Code | EAR99 |
| Resistance | 5.5Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.5mm |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADG622 |
| Output | SEPARATE OUTPUT |
| Pin Count | 10 |
| Qualification Status | Not Qualified |
| Power Supplies | 5/+-5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2.7V |
| Power Dissipation | 10μW |
| Throw Configuration | SPST |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V ±2.7V~5.5V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Max Dual Supply Voltage | 5.5V |
| -3db Bandwidth | 230MHz |
| On-State Resistance (Max) | 5.5Ohm |
| Min Dual Supply Voltage | 2.7V |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 20pF 20pF |
| On-state Resistance Match-Nom | 0.25Ohm |
| Switch Circuit | SPST - NC |
| Switch Time (Ton, Toff) (Max) | 120ns, 70ns |
| Charge Injection | 110pC |
| Channel-to-Channel Matching (ΔRon) | 250m Ω |
| Crosstalk | -90dB @ 1MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-off Time-Max | 70ns |
| Normal Position | NC |
| Height Seated (Max) | 1.1mm |
| Length | 3mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Lead Free |
ADG622BRMZ-REEL Overview
As the electronic part is packed in 10-TFSOP, 10-MSOP (0.118, 3.00mm Width), international shipping is convenient. High reliability is ensured by the advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. 1:1 is the number of circuits in the multiplexer and demultiplexer. Operating temperature around -40°C~85°C TA extended. A total of 10 terminations have been recorded. A 2 channel electronic part produces high-quality output. With a 5V voltage supply, the electrical component should be turned on and run. The electrical component body receives 10 pins. Multiplexers built on a SPST - NC switching circuit are built. Try searching with ADG622 to find analog multiplexer variants. An switch multiplexer with 5.5Ohm internal resistance has a value of 5.5Ohm. To find out what the functions of 10 pins are, please refer to their datasheets. Theswitch device is a typical Multiplexer or Switches. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. 2.7V should be the lowest voltage fed to the electronic component. There is no problem with using dual supply voltage, but it should not exceed 5.5V. A dual power supply should have at least 2.7V voltage attached. The digital multiplexer has SEPARATE OUTPUT outputs that can be used.
ADG622BRMZ-REEL Features
2 Channels
Switch Circuit: SPST - NC
-3db Bandwidth: 230MHz
ADG622BRMZ-REEL Applications
There are a lot of Analog Devices Inc. ADG622BRMZ-REEL Analog Switches & Multiplexers ICs applications.
- Precision test equipment
- DVD-R
- Relay Replacement
- DSUs
- Optical Applications
- Avionics and Military Systems
- Existing multiplexer applications (both fault-protected and nonfault-protected)
- Relay replacements
- FTTH
- CSU
