Parameters |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
3 |
Supply Voltage |
5V |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG633 |
Pin Count |
16 |
Number of Outputs |
6 |
Polarity |
Non-Inverting |
Number of Channels |
1 |
Interface |
Parallel |
Max Supply Voltage |
12V |
Min Supply Voltage |
2V |
Test Frequency |
1MHz |
Operating Supply Current |
10nA |
Nominal Supply Current |
1μA |
Power Dissipation |
10μW |
Max Supply Current |
1μA |
Number of Bits |
1 |
Propagation Delay |
90 ns |
Turn On Delay Time |
95 ns |
Number of Inputs |
3 |
Voltage - Supply, Single/Dual (±) |
2V~12V ±2V~6V |
Supply Type |
Dual, Single |
Bandwidth |
580MHz |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
40 ns |
Max Dual Supply Voltage |
6V |
On-State Resistance (Max) |
75Ohm |
Min Dual Supply Voltage |
2V |
High Level Output Current |
20mA |
Dual Supply Voltage |
5V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
90 dB |
Current - Leakage (IS(off)) (Max) |
200pA |
Channel Capacitance (CS(off), CD(off)) |
4pF 7pF |
On-state Resistance Match-Nom |
0.8Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
95ns, 40ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
800m Ω |
Crosstalk |
-90dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Drain to Source Resistance |
85Ohm |
Height |
1.05mm |
Length |
5mm |
Width |
4.4mm |
Radiation Hardening |
No |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 3 weeks ago) |
Contact Plating |
Tin |
Mounting Type |
Surface Mount |
Package / Case |
16-TSSOP (0.173, 4.40mm Width) |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tube |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
75Ohm |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
10μW |
Technology |
CMOS |
Terminal Form |
GULL WING |
ADG633YRUZ Overview
Shipping overseas is convenient due to the electrical component's packing in 16-TSSOP (0.173, 4.40mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tube. The multiplexer is located in Surface Mount. Multiplexer and demultiplexer circuits have a number 2:1. Operational temperature extended around -40°C~125°C TA. Total terminations are 16. The electronic part provides high-quality output because it has 1 channels. It is safe to turn on and run the electronic component with a 5V voltage supply. It is injected into the electrical part body with 16 pins. A SPDT switching circuit is used to build these analog multiplexers. Try searching with ADG633 if you're looking for variants. It has an internal resistance of 75Ohm. You can find the functions of the 16 pins in the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. In a normalsituation, users should not supply the switches with voltage higher than 12V. A cost-effective Dual, Single supply type analogue multiplexer. There should be 2V voltage fed to the electrical part below 2V. This multiplexer would work with 10nA current. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 6V. If you are using a dual power supply, you should attach at least 2V. A 3 input needs to be operated. There are various bandwidths available for data transfer. This electronic component presents a Drain to Source resistance of 85Ohm. In this digital multiplexer, there are 6 outputs. The switch device is capable of conducting in a 1-bit mode.
ADG633YRUZ Features
1 Channels
Switch Circuit: SPDT
10nA Supply Current
Bandwidth: 580MHz
Drain-to-Source resistance: 85Ohm
1-Bit
ADG633YRUZ Applications
There are a lot of Analog Devices Inc. ADG633YRUZ Analog Switches & Multiplexers ICs applications.
- Channel Banks
- Cell phones
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Fiber to the Home
- Audio and video signal routing
- Cellular phones
- Access Concentrators
- Microwave transmission systems
- DSLAMs
- Battery-powered systems