ADG636YRU
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 14-TSSOP (0.173, 4.40mm Width) |
| Surface Mount | YES |
| Number of Pins | 14 |
| Operating Temperature | -40°C~125°C TA |
| Packaging | Tube |
| JESD-609 Code | e0 |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 14 |
| ECCN Code | EAR99 |
| Resistance | 115Ohm |
| Terminal Finish | Tin/Lead (Sn85Pb15) |
| Subcategory | Multiplexer or Switches |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 235 |
| Number of Functions | 2 |
| Supply Voltage | 5V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 20 |
| Base Part Number | ADG636 |
| Pin Count | 14 |
| Number of Outputs | 4 |
| Power Supplies | 3/5/+-5V |
| Number of Channels | 2 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 2.7V |
| Power Dissipation | 10μW |
| Voltage - Supply, Single/Dual (±) | 2.7V~5.5V ±2.7V~5.5V |
| Neg Supply Voltage-Nom (Vsup) | -5V |
| Max Dual Supply Voltage | 5.5V |
| -3db Bandwidth | 610MHz |
| On-State Resistance (Max) | 115Ohm |
| Min Dual Supply Voltage | 2.7V |
| Multiplexer/Demultiplexer Circuit | 2:1 |
| Off-state Isolation-Nom | 65 dB |
| Current - Leakage (IS(off)) (Max) | 100pA |
| Channel Capacitance (CS(off), CD(off)) | 5pF 8pF |
| On-state Resistance Match-Nom | 2Ohm |
| Switch Circuit | SPDT |
| Switch Time (Ton, Toff) (Max) | 135ns, 80ns |
| Charge Injection | -1.2pC |
| Channel-to-Channel Matching (ΔRon) | 2 Ω |
| Crosstalk | -65dB @ 10MHz |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 135ns |
| Switch-off Time-Max | 80ns |
| Normal Position | NC |
| Height Seated (Max) | 1.1mm |
| Length | 5mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
ADG636YRU Overview
Shipping overseas is convenient due to the electrical component's packing in 14-TSSOP (0.173, 4.40mm Width). The advanced packaging method Tube provides high reliability. Surface Mount is where this multiplexer is located. The ratio between the number of multiplexer and demultiplexer circuits is 2:1. An extended operating temperature of -40°C~125°C TA degrees Celsius. 14 terminations have been made so far. A high-quality output is provided by the electrical component's 2 channels. An 5V voltage supply should allow the electrical part to be turned on and run. An injection of 14 pins is performed into the body of the electrical component. Circuits based on SPDT switching are used to construct these analog switch ics. Try searching with ADG636 to find analog multiplexer variants. There is 115Ohm internal resistance in this digital multiplexer. Datasheets for 14 pin functions are available upon request. There is a standard Multiplexer or Switches analogue multiplexer here. Users should never supply a voltage higher than 5.5V to a switch device. In order for the electronic part to function properly, the lowest voltage should be 2.7V. There's no problem with dual supply voltage for this switch device. However, it shouldn't exceed 5.5V. The voltage should be at least 2.7V if you are using dual power supplies. The analog switch ics includes 4 outputs.
ADG636YRU Features
2 Channels
Switch Circuit: SPDT
-3db Bandwidth: 610MHz
ADG636YRU Applications
There are a lot of Analog Devices Inc. ADG636YRU Analog Switches & Multiplexers ICs applications.
- Industrial control systems
- Signal routing between systems
- New designs requiring multiplexer functions
- HDTV
- Ultrasound
- Cellular phones
- Digital access cross connects
- T1/E1 Terminals
- Microprocessor Controlled Analog Systems
- Audio/video switches
