Parameters |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
80 ns |
Max Dual Supply Voltage |
5.5V |
On-State Resistance (Max) |
115Ohm |
Min Dual Supply Voltage |
2.7V |
Dual Supply Voltage |
5V |
Multiplexer/Demultiplexer Circuit |
2:1 |
Off-state Isolation-Nom |
65 dB |
Current - Leakage (IS(off)) (Max) |
100pA |
Channel Capacitance (CS(off), CD(off)) |
5pF 8pF |
On-state Resistance Match-Nom |
2Ohm |
Switch Circuit |
SPDT |
Switch Time (Ton, Toff) (Max) |
135ns, 80ns |
Charge Injection |
-1.2pC |
Channel-to-Channel Matching (ΔRon) |
2 Ω |
Crosstalk |
-65dB @ 10MHz |
Switching |
BREAK-BEFORE-MAKE |
Normal Position |
NC |
Height Seated (Max) |
1.1mm |
Length |
5mm |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
Mounting Type |
Surface Mount |
Package / Case |
14-TSSOP (0.173, 4.40mm Width) |
Surface Mount |
YES |
Number of Pins |
14 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
14 |
ECCN Code |
EAR99 |
Resistance |
115Ohm |
Terminal Finish |
Tin/Lead (Sn85Pb15) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
10μW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
2 |
Supply Voltage |
5V |
Terminal Pitch |
0.65mm |
Reach Compliance Code |
not_compliant |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG636 |
Output |
SEPARATE OUTPUT |
Pin Count |
14 |
Qualification Status |
Not Qualified |
Number of Channels |
1 |
Interface |
Parallel |
Number of Circuits |
2 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
2.7V |
Operating Supply Current |
1nA |
Power Dissipation |
10μW |
Max Supply Current |
1μA |
Turn On Delay Time |
135 ns |
Voltage - Supply, Single/Dual (±) |
2.7V~5.5V ±2.7V~5.5V |
Supply Type |
Dual, Single |
Bandwidth |
610MHz |
ADG636YRU-REEL Overview
The electronic part can be shipped overseas conveniently because it is packaged in 14-TSSOP (0.173, 4.40mm Width). High reliability is ensured by the advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. Multiplexers and demultiplexers have a number of circuits 2:1. Operating temperature extended to -40°C~125°C TA. Totally, there are 14 terminations. As a result of its 1 channels, this electronic component provides high-quality output. When the electronic component is given a voltage of 5V, it should be turned on and run. As part of its design, the 14 series is equipped with this electronic component. Unlike digital switches, these are based on SPDT switching circuits. It consists of 2 circuits. Try searching for the analog switch ic with ADG636 if you are looking for variants. Analog switches have 115Ohm internal resistance. For details about the functions of 14 pins, please refer to the datasheets. In this analog multiplexer, the value is Multiplexer or Switches. Users should never supply a voltage higher than 5.5V to a switch device. An effective Dual, Single supply digital multiplexer. A low voltage of 2.7V should be applied to the electronic component. 1nA current would be enough for this multiplexer to operate. It may damage the digital multiplexer if the voltage is higher than 1μA. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 5.5V. If you are using a dual power supply, you should attach at least 2.7V. This analog switch ic utilizes SEPARATE OUTPUT output. This switch operates within the bandwidth of 610MHz.
ADG636YRU-REEL Features
1 Channels
Switch Circuit: SPDT
1nA Supply Current
Bandwidth: 610MHz
ADG636YRU-REEL Applications
There are a lot of Analog Devices Inc. ADG636YRU-REEL Analog Switches & Multiplexers ICs applications.
- Digital access cross connects
- Access Concentrators
- Audio signal routing
- Communication systems
- Communications systems
- Digital cross connects (DSX-1)
- High reliability control systems
- Cellular phones
- Remote Powered Equipment
- Power routing