Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 2 weeks ago) |
Mounting Type |
Surface Mount |
Package / Case |
16-SSOP (0.154, 3.90mm Width) |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
75Ohm |
Terminal Finish |
Matte Tin (Sn) |
Max Power Dissipation |
10μW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
5V |
Terminal Pitch |
0.635mm |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
ADG658 |
Pin Count |
16 |
Qualification Status |
Not Qualified |
Operating Supply Voltage |
5V |
Number of Channels |
8 |
Interface |
Parallel |
Number of Circuits |
1 |
Max Supply Voltage |
12V |
Min Supply Voltage |
2V |
Operating Supply Current |
10nA |
Power Dissipation |
10μW |
Throw Configuration |
DPST |
Logic Function |
Multiplexer |
Voltage - Supply, Single/Dual (±) |
2V~12V ±2V~6V |
Supply Type |
Dual, Single |
Bandwidth |
210MHz |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
30 ns |
Max Dual Supply Voltage |
6V |
On-State Resistance (Max) |
75Ohm |
Min Dual Supply Voltage |
2V |
Multiplexer/Demultiplexer Circuit |
8:1 |
Off-state Isolation-Nom |
90 dB |
Current - Leakage (IS(off)) (Max) |
200pA |
Channel Capacitance (CS(off), CD(off)) |
4pF 23pF |
On-state Resistance Match-Nom |
1.3Ohm |
Switch Time (Ton, Toff) (Max) |
115ns, 45ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
1.3 Ω |
Switching |
BREAK-BEFORE-MAKE |
Switch-off Time-Max |
55ns |
Signal Current-Max |
0.02A |
Length |
4.9022mm |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG658YRQZ-REEL7 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 16-SSOP (0.154, 3.90mm Width). High reliability is achieved by using advanced packaging method Tape & Reel (TR). There is an analog multiplexer mounted in position Surface Mount. 8:1 is the ratio between multiplexers and demultiplexers. Increasing operating temperature to around -40°C~125°C TA. 16 terminations have been made so far. The electronic part delivers high-quality output through its 8 channels. When a voltage supply of 5V is used, the electronic component should be turned on and run. There are 16 pins injected into the electronic part body. A total of 1 circuits make up this switch device. Try searching with ADG658 to find analog multiplexer variants. There is 75Ohm internal resistance in this digital multiplexer. To find out what the 16 pins do, please refer to the datasheets. It is normally recommended that users do not supply the multiplexer with voltages higher than 12V. An effective Dual, Single supply digital multiplexer. A low voltage of 2V should be applied to the electronic component. For this multiplexer to operate, 10nA current would be sufficient. It is possible to supply this switch device with dual voltages. However, it is not advisable to exceed 6V. For dual power supplies, a voltage of at least 2V should be attached. This electrical part is compatible with 5V operating voltages. 210MHz bandwidths enable data to be transferred.
ADG658YRQZ-REEL7 Features
8 Channels
10nA Supply Current
Bandwidth: 210MHz
ADG658YRQZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG658YRQZ-REEL7 Analog Switches & Multiplexers ICs applications.
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- Fiber In The Loop (FITL)
- Battery Powered Instruments
- Data Acquisition Systems
- Cell phones
- SDH
- T1/E1 Terminals
- Medical
- Residential Gateways, Home Gateway/Router
- Automotive applications