Parameters |
Pin Count |
16 |
Operating Supply Voltage |
5V |
Number of Channels |
4 |
Number of Circuits |
2 |
Max Supply Voltage |
12V |
Min Supply Voltage |
2V |
Operating Supply Current |
10nA |
Power Dissipation |
10μW |
Throw Configuration |
4PST |
Logic Function |
Multiplexer |
Number of Inputs |
8 |
Voltage - Supply, Single/Dual (±) |
2V~12V ±2V~6V |
Supply Type |
Dual, Single |
Bandwidth |
400MHz |
Supply Current-Max (Isup) |
0.001mA |
Neg Supply Voltage-Nom (Vsup) |
-5V |
Turn-Off Delay Time |
30 ns |
Max Dual Supply Voltage |
6V |
On-State Resistance (Max) |
75Ohm |
Min Dual Supply Voltage |
2V |
Multiplexer/Demultiplexer Circuit |
4:1 |
Off-state Isolation-Nom |
90 dB |
Current - Leakage (IS(off)) (Max) |
200pA |
Channel Capacitance (CS(off), CD(off)) |
4pF 12pF |
On-state Resistance Match-Nom |
1.3Ohm |
Switch Circuit |
SP4T |
Switch Time (Ton, Toff) (Max) |
115ns, 45ns |
Charge Injection |
2pC |
Channel-to-Channel Matching (ΔRon) |
1.3 Ω |
Crosstalk |
-90dB @ 1MHz |
Switching |
BREAK-BEFORE-MAKE |
Switch-off Time-Max |
55ns |
Radiation Hardening |
No |
RoHS Status |
Non-RoHS Compliant |
Lead Free |
Contains Lead |
Mounting Type |
Surface Mount |
Package / Case |
16-SSOP (0.154, 3.90mm Width) |
Surface Mount |
YES |
Number of Pins |
16 |
Operating Temperature |
-40°C~125°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e0 |
Pbfree Code |
no |
Part Status |
Obsolete |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
16 |
ECCN Code |
EAR99 |
Resistance |
75Ohm |
Max Power Dissipation |
10μW |
Technology |
CMOS |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
240 |
Number of Functions |
1 |
Supply Voltage |
5V |
Terminal Pitch |
0.635mm |
Time@Peak Reflow Temperature-Max (s) |
30 |
Base Part Number |
ADG659 |
ADG659YRQ-REEL Overview
Due to its 16-SSOP (0.154, 3.90mm Width) packaging, the electronic part is convenient for international shipping. The advanced packaging method Tape & Reel (TR) provides high reliability. It is mounted in the position Surface Mount. Multiplexers and demultiplexers have the same number of circuits 4:1. Operating temperature extended to -40°C~125°C TA. The total number of terminations is 16. A electrical component with 4 channels is capable of high-quality output. Powered by a 5V voltage supply, the electrical part should be switched on and run. As part of its design, the 16 series is equipped with this electronic component. Multiplexers built on a SP4T switching circuit are built. This multiplexer is composed of 2 circuits. Look for analog switch ic variants by searching with ADG659. The internal resistance of this digital multiplexer is 75Ohm. To find out what the functions of 16 pins are, please refer to their datasheets. Users shouldn't supply more than 12V voltage to the switch device. The analog switch ic is of the Dual, Single supply type and is cost-effective. The lowest voltage fed to the electronic component should be 2V. For this multiplexer to operate, 10nA current would be sufficient. Dual supply volatge is feasible for this multiplexer. But it should not go beyond 6V. For dual power supplies, a voltage of at least 2V should be attached. 5V operating voltages are supported by the electronic component. Operating 8 inputs is required. In 400MHz-bandwidths, data can be transferred.
ADG659YRQ-REEL Features
4 Channels
Switch Circuit: SP4T
10nA Supply Current
Bandwidth: 400MHz
ADG659YRQ-REEL Applications
There are a lot of Analog Devices Inc. ADG659YRQ-REEL Analog Switches & Multiplexers ICs applications.
- Communications systems
- Avionics test equipment
- Private Branch Exchange (PBX)
- USB 1.1 signal switching circuits
- Sample-and-hold systems
- Voice over IP/DSL – Integrated Access Devices, Smart
- Cable Modem
- Battery Powered Instruments
- Industrial
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads