ADG701BRJ-500RL7
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Supplier Device Package | SOT-23-5 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Resistance | 3Ohm |
| Max Operating Temperature | 85°C |
| Min Operating Temperature | -40°C |
| Max Power Dissipation | 5μW |
| Base Part Number | ADG701 |
| Number of Outputs | 1 |
| Number of Channels | 1 |
| Interface | Parallel |
| Number of Circuits | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Number of Bits | 1 |
| Throw Configuration | SPST |
| Turn On Delay Time | 12 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 8 ns |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 3Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Current - Leakage (IS(off)) (Max) | 10pA Typ |
| Channel Capacitance (CS(off), CD(off)) | 17pF 17pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 12ns, 8ns (Typ) |
| Charge Injection | 5pC |
| Voltage - Supply, Single (V+) | 1.8V~5V |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG701BRJ-500RL7 Overview
As the electronic part is packed in SC-74A, SOT-753, international shipping is convenient. This packaging method provides high reliability because it uses advanced packaging techniques. Multiplexers like this are mounted in the Surface Mount position. There is 1:1 ratio between the number of multiplexers and demultiplexers. Operation at a temperature around -40°C~85°C TA. A high-quality output is provided by the electrical component's 1 channels. SPST - NO switching circuits are used in these analog switch ics. 1 circuits are used in this analogue multiplexer. If you are looking for variants of the digital switch, trying search with ADG701. It has an internal resistance of 3Ohm. To find out what the functions of 5 pins are, please refer to their datasheets. normally, users should not supply switches with voltages higher than 5.5V. A cost-effective Single supply type analogue multiplexer. It is recommended to use 1.8V as the lowest voltage for the electrical part. It would be sufficient to run this analogue multiplexer with 1nA current. Using only a single voltage supply, this analog switch requires 1.8V~5V voltage. Put voltage above 1μA on the multiplexer to cause damage. Among the inputs that can be operated are the 1 inputs. In 200MHz-bandwidths, data can be transferred. An environment with a temperature greater than 85°C should not be used to operate the digital switches. An output of 1 is provided by the digital multiplexer. There is a SOT-23-5 package offered by suppliers. 1-bits are supported.
ADG701BRJ-500RL7 Features
1 Channels
Switch Circuit: SPST - NO
1nA Supply Current
-3db Bandwidth: 200MHz
Bandwidth: 200MHz
1-Bit
ADG701BRJ-500RL7 Applications
There are a lot of Analog Devices Inc. ADG701BRJ-500RL7 Analog Switches & Multiplexers ICs applications.
- Industrial
- Remote wireless modules
- Avionics test equipment
- Cross Connects
- ATM
- FTTH
- Medical Instrumentation
- PBX interfaces
- Communications systems
- DSUs
