ADG701BRJ-REEL7
| Parameters | |
|---|---|
| Contact Plating | Lead, Tin |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 3Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG701 |
| Pin Count | 5 |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 12 ns |
| Supply Type | Single |
| Turn-Off Delay Time | 8 ns |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 3Ohm |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 10pA Typ |
| Channel Capacitance (CS(off), CD(off)) | 17pF 17pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 12ns, 8ns (Typ) |
| Charge Injection | 5pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 20ns |
| Voltage - Supply, Single (V+) | 1.8V~5V |
| Normal Position | NO |
| Length | 2.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG701BRJ-REEL7 Overview
The electrical component comes in SC-74A, SOT-753 packaging, which makes it convenient to ship overseas. High reliability is ensured by the advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. 1:1 is the ratio between multiplexers and demultiplexers. Operation at a temperature around -40°C~85°C TA. Total terminations are 5. A 1 channel electronic part produces high-quality output. In the case of a voltage supply of 3V volts, the electrical part can be powered up and run. The electronic part body is injected with 5 pins. Multiplexers built on a SPST - NO switching circuit are built. Use ADG701 to search for variants of the digital switches. The internal resistance of this digital multiplexer is 3Ohm. Datasheets for functions of 5 pins are available. Theswitch device is a typical Multiplexer or Switches. Users should never supply a voltage higher than 5.5V to a switch device. Analogue multiplexer with a Single supply type that is cost-effective. The lowest voltage fed to the electronic component should be 1.8V. 1nA current would be enough for this multiplexer to operate. This analogue multiplexer requires a voltage of 1.8V~5V when it drains from a single voltage supply. If put voltage greater than 1μA on the device, damage may be caused to the analogue multiplexer.
ADG701BRJ-REEL7 Features
1 Channels
Switch Circuit: SPST - NO
1nA Supply Current
-3db Bandwidth: 200MHz
ADG701BRJ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG701BRJ-REEL7 Analog Switches & Multiplexers ICs applications.
- Battery Powered Systems
- Medical systems
- USB 1.1 signal switching circuits
- Avionics and Military Systems
- Medical
- Routers
- Microwave transmission systems
- PBX interfaces
- Public switching systems
- Power routing
