ADG701BRMZ-REEL7
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 3Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG701 |
| Pin Count | 8 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Nominal Supply Current | 1μA |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 12 ns |
| Supply Type | Single |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 8 ns |
| On-State Resistance (Max) | 3Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 10pA Typ |
| Channel Capacitance (CS(off), CD(off)) | 17pF 17pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 12ns, 8ns (Typ) |
| Charge Injection | 5pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 20ns |
| Voltage - Supply, Single (V+) | 1.8V~5V |
| Normal Position | NO |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 3 weeks ago) |
| Mount | Surface Mount |
ADG701BRMZ-REEL7 Overview
Shipping overseas is convenient with the electronic component packed in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). This packaging method provides high reliability because it uses advanced packaging techniques. It is mounted in the position Surface Mount. 1:1 is the ratio of multiplexer to demultiplexer circuits. An extended operating temperature of -40°C~85°C TA degrees Celsius. 8 terminations have been made so far. Due to its 1 channels, the electrical component produces high-quality output. An 3V voltage supply should allow the electrical part to be turned on and run. Electronic part bodies are injected with 8 pins. SPST - NO switching circuits are used in these analog switch ics. Try searching with ADG701 to find analog multiplexer variants. Analog switches have 3Ohm internal resistance. To find out what the 8 pins do, please refer to the datasheets. There is Multiplexer or Switches analog multiplexer like this in the world. In normalcircumstances, users should not exceed 5.5V volts for the multiplexer. Single supply type digital switch with a low cost. 1.8V is the lowest voltage that should be fed to the electronic electronic part. For this digital switch to work, 1nA current would suffice. An analogue multiplexer drains from a single voltage supply at 1.8V~5V. When the digital multiplexer is charged above 1μA, damage can occur. A 200MHz-bandwidth can be used for data transfer.
ADG701BRMZ-REEL7 Features
1 Channels
Switch Circuit: SPST - NO
1nA Supply Current
Bandwidth: 200MHz
ADG701BRMZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG701BRMZ-REEL7 Analog Switches & Multiplexers ICs applications.
- Central office
- Battery-powered systems
- High reliability control systems
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- Isolation
- Medical
- Multi-Line E1 Interface Cards
- Remote Powered Equipment
- E1 Multiplexer
- MP3 players
