ADG701BRT-REEL7
| Parameters | |
|---|---|
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 3Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 30 |
| Base Part Number | ADG701 |
| Pin Count | 6 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 12 ns |
| Supply Type | Single |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 8 ns |
| On-State Resistance (Max) | 3Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 10pA Typ |
| Channel Capacitance (CS(off), CD(off)) | 17pF 17pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 12ns, 8ns (Typ) |
| Charge Injection | 5pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 20ns |
| Voltage - Supply, Single (V+) | 1.8V~5V |
| Normal Position | NO |
| Length | 2.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG701BRT-REEL7 Overview
This electronic part is conveniently packaged in SOT-23-6, making it easy to ship abroad. High reliability is provided by advanced packaging method Tape & Reel (TR). Multiplexers like this are mounted in the Surface Mount position. The ratio between the number of multiplexer and demultiplexer circuits is 1:1. An extended operating temperature of -40°C~85°C TA degrees Celsius. The total number of terminations is 6. The electronic part provides high-quality output because it has 1 channels. Turning on and running the electrical part should be easy with a 3V voltage supply. Electronic part bodies are injected with 6 pins. Unlike digital switches, these are based on SPST - NO switching circuits. Try searching for the analog switch ic with ADG701 if you are looking for variants. A 3Ohm internal resistance characterizes this multiplexer. You can find the functions of the 6 pins in the datasheets. It is a typical Multiplexer or Switches analog multiplexer. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. The analog switch ic is of the Single supply type and is cost-effective. 1.8V is the lowest voltage the electrical component should receive. The analogue multiplexer could operate on 1nA current. The voltage required by this switch device is 1.8V~5V, draining from a single voltage supply. The switch multiplexer may be damaged if it is exposed to voltage greater than 1μA. It is possible to transfer data over a 200MHz-bandwidth.
ADG701BRT-REEL7 Features
1 Channels
Switch Circuit: SPST - NO
1nA Supply Current
Bandwidth: 200MHz
ADG701BRT-REEL7 Applications
There are a lot of Analog Devices Inc. ADG701BRT-REEL7 Analog Switches & Multiplexers ICs applications.
- Access Concentrators
- Relay replacements
- Routers
- Voice over IP/DSL – Integrated Access Devices, Smart
- Cellular phones
- SDH
- Private Branch Exchange (PBX)
- Avionics
- Short/Medium Loop: approximately 2000 ft. of 26 AWG and 5 REN loads
- FTTH
