ADG701BRTZ-REEL7
| Parameters | |
|---|---|
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 10pA Typ |
| Channel Capacitance (CS(off), CD(off)) | 17pF 17pF |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 12ns, 8ns (Typ) |
| Charge Injection | 5pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 20ns |
| Voltage - Supply, Single (V+) | 1.8V~5V |
| Normal Position | NO |
| Height | 1.3mm |
| Length | 2.9mm |
| Width | 1.6mm |
| Radiation Hardening | No |
| REACH SVHC | No SVHC |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
| Factory Lead Time | 1 Week |
| Lifecycle Status | PRODUCTION (Last Updated: 1 month ago) |
| Mount | Surface Mount |
| Mounting Type | Surface Mount |
| Package / Case | SOT-23-6 |
| Number of Pins | 6 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | no |
| Part Status | Active |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 6 |
| ECCN Code | EAR99 |
| Resistance | 3Ohm |
| Terminal Finish | Matte Tin (Sn) |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.95mm |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADG701 |
| Pin Count | 6 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Interface | Parallel |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 12 ns |
| Bandwidth | 200MHz |
| Turn-Off Delay Time | 8 ns |
| On-State Resistance (Max) | 3Ohm |
ADG701BRTZ-REEL7 Overview
Packed in SOT-23-6, the electronic component is convenient for shipping overseas. This high-reliability packaging method uses advanced packaging methods Tape & Reel (TR). Surface Mount is where this multiplexer is located. Multiplexers and demultiplexers have the same number of circuits 1:1. Around -40°C~85°C TA is the extended operating temperature. In total, there are 6 terminations. Due to its 1 channels, the electrical component produces high-quality output. With a 3V voltage supply, the electrical component should be turned on and run. As part of the design of the 6 series, this electronic part has been incorporated into the system. Unlike digital switches, these are based on SPST - NO switching circuits. Look for analog switch ic variants by searching with ADG701. This digital multiplexer has 3Ohm internal resistance. The datasheets for the 6 pins explain the functions. This switch device is a typical Multiplexer or Switches. In a normalsituation, users should not supply the switches with voltage higher than 5.5V. 1.8V is the lowest voltage that should be fed to the electronic electronic part. Using only a single voltage supply, this analog switch requires 1.8V~5V voltage. Put voltage above 1μA on the multiplexer to cause damage. The transfer of data can be performed over 200MHz bandwidths.
ADG701BRTZ-REEL7 Features
1 Channels
Switch Circuit: SPST - NO
Bandwidth: 200MHz
ADG701BRTZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG701BRTZ-REEL7 Analog Switches & Multiplexers ICs applications.
- Medical systems
- High-Voltage
- Communication systems
- DSUs
- Cable Modem
- ATM
- Voice over IP/DSL – Integrated Access Devices, Smart
- Cable Telephony – NIU, Set-Top Box, Home Side Box
- PCMCIA cards
- SDH
