ADG701LBRJ-REEL7
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 3Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Base Part Number | ADG701 |
| Output | SEPARATE OUTPUT |
| Pin Count | 5 |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Operating Supply Current | 1nA |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 12 ns |
| Number of Inputs | 1 |
| Supply Type | Single |
| Turn-Off Delay Time | 8 ns |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 3Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 17pF 17pF |
| On-state Resistance Match-Nom | 1.5Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 12ns, 8ns (Typ) |
| Charge Injection | 5pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 20ns |
| Voltage - Supply, Single (V+) | 1.8V~5V |
| Normal Position | NC |
| Length | 2.9mm |
| Radiation Hardening | No |
| RoHS Status | Non-RoHS Compliant |
| Lead Free | Contains Lead |
ADG701LBRJ-REEL7 Overview
The electronic part can be shipped overseas conveniently because it is packaged in SC-74A, SOT-753. High reliability is achieved by using advanced packaging method Tape & Reel (TR). A switch device like this is mounted in Surface Mount. 1:1 is the ratio between multiplexers and demultiplexers. Operating temperature around -40°C~85°C TA extended. A total of 5 terminations have been recorded. The electronic part provides high-quality output because it has 1 channels. Powered by a 3V voltage supply, the electrical part should be switched on and run. An electrical component of this type can be found in the 5 series. A SPST - NO switching circuit is used for these analog switches. ADG701 can be used to search for analog multiplexer variants. It has an internal resistance of 3Ohm. For details about the functions of 5 pins, please refer to the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. A voltage higher than 5.5V should not normally be supplied to the switches. A analog switch ic that has a cost-effective Single supply type. The lowest voltage the electronic part should receive is 1.8V. In order to operate this switch device, it would need a current of 1nA. A voltage of 1.8V~5V is required to drain this analog switch from a single voltage supply. If you put voltage higher than 1μA on the digital multiplexer, damage may occur. A total of SEPARATE OUTPUT outputs are available on this analog switch ic. Operating 1 inputs is required.
ADG701LBRJ-REEL7 Features
1 Channels
Switch Circuit: SPST - NO
1nA Supply Current
-3db Bandwidth: 200MHz
ADG701LBRJ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG701LBRJ-REEL7 Analog Switches & Multiplexers ICs applications.
- Digital cross connects (DSX-1)
- Battery Powered Instruments
- Fault Tolerant Systems
- HDTV
- ADCs such as AD7840/8, AD7870/1/2/4/5/6/8
- Medical systems
- PDH Multiplexers
- Public switching systems
- Digital access cross connects
- Data Acquisition Systems
