ADG701LBRJZ-REEL
| Parameters | |
|---|---|
| Contact Plating | Tin |
| Mounting Type | Surface Mount |
| Package / Case | SC-74A, SOT-753 |
| Surface Mount | YES |
| Number of Pins | 5 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e3 |
| Pbfree Code | yes |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 5 |
| ECCN Code | EAR99 |
| Resistance | 3Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 260 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Reach Compliance Code | unknown |
| Time@Peak Reflow Temperature-Max (s) | 40 |
| Base Part Number | ADG701 |
| Pin Count | 5 |
| Qualification Status | Not Qualified |
| Polarity | Non-Inverting |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Turn On Delay Time | 12 ns |
| Number of Inputs | 1 |
| Turn-Off Delay Time | 8 ns |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 3Ohm |
| High Level Output Current | 30mA |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 17pF 17pF |
| On-state Resistance Match-Nom | 1.5Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 12ns, 8ns (Typ) |
| Charge Injection | 5pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 20ns |
| Voltage - Supply, Single (V+) | 1.8V~5V |
| Normal Position | NC |
| Length | 2.9mm |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG701LBRJZ-REEL Overview
Packed in SC-74A, SOT-753, the electronic component is convenient for shipping overseas. A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). Mounted in Surface Mount is this multiplexer. Multiplexers and demultiplexers have a ratio of 1:1. Operation at a temperature around -40°C~85°C TA. In total, there have been 5 terminations. By its 1 channels, the electronic component provides high-quality output. With a 3V voltage supply, the electrical component should be turned on and run. There are 5 pins injected into the electronic part body. The analog switch ics are built using SPST - NO switching circuits. Try searching with ADG701 if you're looking for variants. A 3Ohm internal resistance characterizes this multiplexer. You can find the functions of the 5 pins in the datasheets. A analogue multiplexer of this type is a Multiplexer or Switches. It is generally not recommended to supply a voltage higher than 5.5V to the switch device in normal circumstances. In order for the electronic part to function properly, the lowest voltage should be 1.8V. This analogue multiplexer requires a voltage of 1.8V~5V when it drains from a single voltage supply. Put voltage above 1μA on the multiplexer to cause damage. The 1 inputs need to be operated in order to work.
ADG701LBRJZ-REEL Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 200MHz
ADG701LBRJZ-REEL Applications
There are a lot of Analog Devices Inc. ADG701LBRJZ-REEL Analog Switches & Multiplexers ICs applications.
- T1/E1 Terminals
- Communication systems
- FTTH
- Automotive applications
- Sample-and-hold systems
- Mechanical reed relay replacement
- Voice over IP/DSL – Integrated Access Devices, Smart
- Cable Modem
- Signal routing between systems
- Channelized and Unchannelized DS3 applications
