Parameters |
Factory Lead Time |
1 Week |
Lifecycle Status |
PRODUCTION (Last Updated: 3 weeks ago) |
Mounting Type |
Surface Mount |
Package / Case |
SC-74A, SOT-753 |
Surface Mount |
YES |
Number of Pins |
5 |
Operating Temperature |
-40°C~85°C TA |
Packaging |
Tape & Reel (TR) |
JESD-609 Code |
e3 |
Pbfree Code |
no |
Part Status |
Active |
Moisture Sensitivity Level (MSL) |
1 (Unlimited) |
Number of Terminations |
5 |
ECCN Code |
EAR99 |
Resistance |
3Ohm |
Terminal Finish |
Matte Tin (Sn) |
Subcategory |
Multiplexer or Switches |
Max Power Dissipation |
5μW |
Technology |
CMOS |
Terminal Position |
DUAL |
Terminal Form |
GULL WING |
Peak Reflow Temperature (Cel) |
260 |
Number of Functions |
1 |
Supply Voltage |
3V |
Time@Peak Reflow Temperature-Max (s) |
40 |
Base Part Number |
ADG701 |
Output |
SEPARATE OUTPUT |
Pin Count |
5 |
Qualification Status |
Not Qualified |
Number of Channels |
1 |
Max Supply Voltage |
5.5V |
Min Supply Voltage |
1.8V |
Test Frequency |
1MHz |
Operating Supply Current |
1nA |
Power Dissipation |
5μW |
Max Supply Current |
1μA |
Throw Configuration |
SPST |
Turn On Delay Time |
12 ns |
Number of Inputs |
1 |
Supply Type |
Single |
Bandwidth |
200MHz |
Turn-Off Delay Time |
8 ns |
On-State Resistance (Max) |
3Ohm |
Multiplexer/Demultiplexer Circuit |
1:1 |
Off-state Isolation-Nom |
55 dB |
Current - Leakage (IS(off)) (Max) |
250pA |
Channel Capacitance (CS(off), CD(off)) |
17pF 17pF |
On-state Resistance Match-Nom |
1.5Ohm |
Switch Circuit |
SPST - NO |
Switch Time (Ton, Toff) (Max) |
12ns, 8ns (Typ) |
Charge Injection |
5pC |
Switching |
BREAK-BEFORE-MAKE |
Switch-on Time-Max |
20ns |
Voltage - Supply, Single (V+) |
1.8V~5V |
Drain to Source Resistance |
4Ohm |
Normal Position |
NC |
Length |
2.9mm |
REACH SVHC |
No SVHC |
RoHS Status |
ROHS3 Compliant |
Lead Free |
Contains Lead |
ADG701LBRJZ-REEL7 Overview
Due to its SC-74A, SOT-753 packaging, the electronic part is convenient for international shipping. High reliability is achieved by using advanced packaging method Tape & Reel (TR). In Surface Mount, this analog switch is mounted. Multiplexers and demultiplexers have a number of circuits 1:1. Operating temperature around -40°C~85°C TA extended. A total of 5 terminations have been recorded. By its 1 channels, the electronic component provides high-quality output. A 3V voltage supply should turn on and run the electronic component. There are 5 pins injected into the electronic part body. Circuits based on SPST - NO switching are used to construct these analog switch ics. Try searching with ADG701 if you're looking for variants. In this multiplexer, the internal resistance is 3Ohm. For details about the functions of 5 pins, please refer to the datasheets. There is a standard Multiplexer or Switches analogue multiplexer here. An abnormal situation would be for the switch device to be supplied with a voltage greater than 5.5V. Digital switch that provides Single power at a cost-effective price. It is recommended to use 1.8V as the lowest voltage for the electrical part. In order to operate this switch device, it would need a current of 1nA. This analogue multiplexer requires a voltage of 1.8V~5V when it drains from a single voltage supply. A digital multiplexer may suffer damage if voltage is applied above 1μA. The analog switch ic utilizes SEPARATE OUTPUT outputs in total. In order to operate the 1 inputs, there are several steps to follow. The transfer of data can be performed over 200MHz bandwidths. It has a Drain to Source resistance of 4Ohm ohms.
ADG701LBRJZ-REEL7 Features
1 Channels
Switch Circuit: SPST - NO
1nA Supply Current
Bandwidth: 200MHz
Drain-to-Source resistance: 4Ohm
ADG701LBRJZ-REEL7 Applications
There are a lot of Analog Devices Inc. ADG701LBRJZ-REEL7 Analog Switches & Multiplexers ICs applications.
- Avionics and Military Systems
- Wireless Local Loop
- Medical
- Fault Tolerant Systems
- Precision instrumentation
- FTTH
- Microprocessor controlled systems
- CSU
- Signal routing between systems
- SONET