ADG701LBRM-REEL7
| Parameters | |
|---|---|
| Mounting Type | Surface Mount |
| Package / Case | 8-TSSOP, 8-MSOP (0.118, 3.00mm Width) |
| Surface Mount | YES |
| Number of Pins | 8 |
| Operating Temperature | -40°C~85°C TA |
| Packaging | Tape & Reel (TR) |
| JESD-609 Code | e0 |
| Pbfree Code | no |
| Part Status | Obsolete |
| Moisture Sensitivity Level (MSL) | 1 (Unlimited) |
| Number of Terminations | 8 |
| ECCN Code | EAR99 |
| Resistance | 3Ohm |
| Subcategory | Multiplexer or Switches |
| Max Power Dissipation | 5μW |
| Technology | CMOS |
| Terminal Position | DUAL |
| Terminal Form | GULL WING |
| Peak Reflow Temperature (Cel) | 240 |
| Number of Functions | 1 |
| Supply Voltage | 3V |
| Terminal Pitch | 0.65mm |
| Base Part Number | ADG701 |
| Output | SEPARATE OUTPUT |
| Pin Count | 8 |
| Power Supplies | 3/5V |
| Number of Channels | 1 |
| Max Supply Voltage | 5.5V |
| Min Supply Voltage | 1.8V |
| Power Dissipation | 5μW |
| Max Supply Current | 1μA |
| Throw Configuration | SPST |
| Turn On Delay Time | 12 ns |
| Turn-Off Delay Time | 8 ns |
| -3db Bandwidth | 200MHz |
| On-State Resistance (Max) | 3Ohm |
| Multiplexer/Demultiplexer Circuit | 1:1 |
| Off-state Isolation-Nom | 55 dB |
| Current - Leakage (IS(off)) (Max) | 250pA |
| Channel Capacitance (CS(off), CD(off)) | 17pF 17pF |
| On-state Resistance Match-Nom | 1.5Ohm |
| Switch Circuit | SPST - NO |
| Switch Time (Ton, Toff) (Max) | 12ns, 8ns (Typ) |
| Charge Injection | 5pC |
| Switching | BREAK-BEFORE-MAKE |
| Switch-on Time-Max | 20ns |
| Voltage - Supply, Single (V+) | 1.8V~5V |
| Normal Position | NC |
| Length | 3mm |
| Radiation Hardening | No |
| RoHS Status | ROHS3 Compliant |
| Lead Free | Contains Lead |
ADG701LBRM-REEL7 Overview
The electronic part can be shipped overseas conveniently because it is packaged in 8-TSSOP, 8-MSOP (0.118, 3.00mm Width). A high level of reliability can be achieved through the use of an advanced packaging method Tape & Reel (TR). It is mounted in the position Surface Mount. Multiplexer and demultiplexer circuits have a number 1:1. Around -40°C~85°C TA is the extended operating temperature. 8 terminations have been made so far. As a result of its 1 channels, this electronic component provides high-quality output. Turning on and running the electrical part should be easy with a 3V voltage supply. As part of its design, the 8 series is equipped with this electronic component. A SPST - NO switching circuit is used for these analog switches. Try searching with ADG701 if you're looking for variants. As far as internal resistance is concerned, it has 3Ohm. The datasheets for the 8 pins explain the functions. The analog multiplexer shown here is a typical Multiplexer or Switches. It is normally recommended that users do not supply the multiplexer with voltages higher than 5.5V. A low voltage of 1.8V should be applied to the electronic component. This analog switch requires a voltage of 1.8V~5V to drain from a single voltage supply. A digital multiplexer may suffer damage if voltage is applied above 1μA. The digital multiplexer has SEPARATE OUTPUT outputs that can be used.
ADG701LBRM-REEL7 Features
1 Channels
Switch Circuit: SPST - NO
-3db Bandwidth: 200MHz
ADG701LBRM-REEL7 Applications
There are a lot of Analog Devices Inc. ADG701LBRM-REEL7 Analog Switches & Multiplexers ICs applications.
- Digital cross connects (DSX-1)
- Multi-Line E1 Interface Cards
- Audio and video routing
- Digital Cross-Connects
- Mechanical reed relay replacement
- Multiplexers
- Avionics and Military Systems
- SDH
- DVD-R
- Channel Banks
